Konica Minolta bizhub 420 User Manual

							7Finishing/Folding
Downloaded From ManualsPrinter.com Manuals 
						

							Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-3
7 Finishing/Folding
7.1 Output for Machine without Finisher
The output tray OT-501 is installed in the 
main unit without a finisher as illustrated 
right. The machine is available to select the 
following four output modes. 
As the default setting, Sort is selected.
-Sort
Select this setting to separate each set of a multi-page original.
-Group
Select this setting to separate the copies of each page in a multi-page 
original.
-Sort and Offset
Select this setting to rotate every other set by 90° upon exit, provided the 
same paper size is loaded in two trays, one tray with paper loaded in 
crosswise orientation v and the other tray with paper loaded in 
lengthwise orientation w, e.g., A4- or B5-size paper. 
-Group and Offset
Select this setting to rotate every other grouped set by 90° upon exit, 
provided the same paper size is loaded in two trays, one tray with paper 
loaded in crosswise orientation v and the other tray with paper loaded in 
lengthwise orientation w, e.g., A4- or B5-size paper. 
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-4 bizhub 500/420/360 (Phase 3)Function overview
ModeSample
Sort
Group
Sort and Offset
Group and Offset
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-5To specify output mode
0As the default setting, Group is selected. When 2 sets or more are 
entered, automatically output in sort mode. 
0Some copy condition is incompatible with Group. For details, see Copy 
Conditions Incompatible with Finishing/Folding on page 7-32.
0If no finisher is installed and the following conditions are met, printed 
copies can be fed out and sorted in an alternating crisscross pattern.
A4- or B5-size paper is used.
Paper of the same size and type is loaded with the crosswise orientation 
v in one paper tray and with the lengthwise orientation w in other tray.
Auto Paper Select setting is selected.
The Auto Paper Select setting is not selected when the Mixed Original 
setting is selected.
0The output tray capacity is max. 250 sheets. If a copy run of more than 
250 is required, be sure to remove the copies from the output tray before 
the maximum capacity is reached.
1Position the original to be copied.
2Using the keypad, enter the desired number of copies.
3Load copy paper into the tray.
– When using an alternating crisscross pattern, load A4- or B5-size 
paper with portrait orientation v in one paper tray and with the 
landscape orientation w in other tray.
4Touch [Finishing] on the Basic Screen.
The Finishing Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-6 bizhub 500/420/360 (Phase 3)
5Select Sort or Group, and set Offset to use offset output.
– To set sort, touch [Sort] to highlight it.
– To set group, touch [Group] to highlight it.
– To set sort in alternating crisscross pattern, touch [Sort] and [Offset] 
to highlight them.
– To set group in alternating crisscross pattern, touch [Group] and 
[Offset] to highlight them.
6Touch [OK].
The Basic Screen will be restored.
7Specify any necessary copy settings.
– Auto Paper Select may be released automatically depending on the 
setting you made.
When using Crisscross sorting or Crisscross grouping, make sure 
that other copy conditions do not conflict with Auto Paper Select.
8Press [Start].
The scan/print job will start.
2
Note 
To cancel changes to the settings, touch [Cancel] on the Finishing 
Screen.
To cancel all settings, press [Reset].
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-7
7.2 Output for Machine with Finisher
The machine with Finisher FS-510/FS-511 provides output modes as 
described below.
As factory default, Finisher FS-510 is set to output the printed sheets to tray 
1 in Group mode.
As factory default, Finisher FS-511 is set to output the printed sheets to 
primary tray (tray 2) in Group mode.
-Sort
Select this setting to separate each set of a multi-page original.
-Group
Select this setting to separate the copies of each page in a multi-page 
original.
-Sort + Offset
Select this setting to output multiple copies of the original set; each 
sorted set will be offset by 30 mm upon exit. 
(Secondary tray (tray 1) of Finisher FS-511 is unavailable.)
-Group + Offset
Select this setting to group together multiple copies of each original and 
offsets the sets by 30 mm upon exit.
(Secondary tray (tray 1) of Finisher FS-511 is unavailable.)
2
Note 
Finisher FS-510 is initially equipped with two exit trays, and one optional 
output tray OT-601 can be installed. Contact your service representative, 
if desired. (Optional output tray is installed in Finisher illustrated above)
Finisher FS-510 is available to output in each tray using every output 
mode.
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-8 bizhub 500/420/360 (Phase 3)Function overview
ModeSample
Sort
Group
Sort + Offset
Group + Offset
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-9To specify finisher output mode
0As the default setting, Sort is selected. No limit is established in Sort 
mode.
0Some copy conditions are incompatible with Group mode. For details, 
see Copy Conditions Incompatible with Finishing/Folding on 
page 7-32.
0When making copies using postcard, trace, or OHP transparencies on 
the machine with Finisher FS-511 installed, be sure that the Secondary 
(sub) tray is selected as an output tray.
0Each output tray of Finisher FS-510 and FS-511 has a limit in capacity. 
Be careful not to exceed the limit. For details, see Paper Tray/ Output 
Tray Capacity on page 10-5.
1Position the original to be copied.
2Using the keypad, enter the desired number of copies.
3Touch [Finishing] on the Basic Screen.
The Finishing Screen will be displayed.
4Select Sort or Group, and set Offset to use offset output.
– To set Sort mode, touch [Sort] to highlight it.
– To set Group mode, touch [Group] to highlight it.
– To set Sort in offset output, touch [Sort] and [Offset] to highlight 
them.
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-10 bizhub 500/420/360 (Phase 3)– To set Group in offset output, touch [Group] and [Offset] to highlight 
them.
– To cancel the setting, touch the key again to deselect it.
5Touch [OK].
The Basic Screen will be restored.
6Specify any necessary copy settings.
7Press [Start].
The scan/print job will start.
2
Reminder 
Finisher FS-510 trays gradually go up/down while printed materials 
output, depending on the tray selected.With Saddle Stitcher SD-502 or 
Mailbin Kit MT-501, the operation of the trays become greater. DO NOT 
allow any object to interfere with the operation of the tray around the 
finisher, as any interference may cause damage to the finisher.
Finisher FS-511 tray 2 (main tray) gradually goes down while printed 
materials output. DO NOT allow any object to interfere with the operation 
of the tray 2 (main tray) on the left side of the finisher, as any interference 
may cause damage to the finisher.
Downloaded From ManualsPrinter.com Manuals