Konica Minolta bizhub 420 User Manual

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-11
2
Note 
To cancel changes to the settings, touch [Cancel] on the Finishing 
Screen.
To cancel all settings, press [Reset].
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-12 bizhub 500/420/360 (Phase 3)
7.3 Stapling Output Copies (Staple)
The following types of machine with a finisher installed can provide Staple 
output mode.
2
Note 
Finisher FS-510 is initially equipped with two exit trays, and one optional 
exit tray (OT-601) can be installed. Contact your service representative, if 
desired. (Already installed in the above illustration.)
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-13Function overview
The Original Direction setting for the samples below is supposed to be the 
one which the top of the original is aligned to the rear side of the machine.
KeySample
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-14 bizhub 500/420/360 (Phase 3)
KeySample
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-15To copy using Staple mode
0If Staple is to be selected, select the orientation in which the original is 
positioned and the orientation of the page to be stapled, otherwise the 
copies may not be stapled as desired.
0If Staple is selected, the machine also selects Sort automatically with 
disabling Group and Offset. Each copied set is supposed to be sorted 
and stapled.
0If staple position setting is different from the binding position specified in 
Page Margin of Application setting, the staple position is given priority.
0With Auto selected on the Staple Position popup menu, the staple 
position will be determined automatically to the longer side for A4 copy 
paper, or to the shorter side for copy paper larger than A4.
0Available paper weight is 60 to 90 gm
2. For details of other specifications, 
see Paper Weight on page 10-4.
0Using excessively curled paper or some types of thin paper in Staple 
mode may cause poor results in arrangement of the stapled sets.
0Each output tray of Finisher FS-510 and FS-511 has a limit in capacity. 
Be careful not to exceed the limit. For details, see Paper Tray/ Output 
Tray Capacity on page 10-5.
1Position the original to be copied.
2Using the keypad, enter the desired number of copies.
3Touch [Combine Originals] tab on the Basic Screen, then make Original 
Direction and Margin settings.
– For setting Original Direction, see Specifying Orientation of 
Original (Original Direction) on page 5-14.
For setting Margin, see Paper Tray/ Output Tray Capacity on 
page 10-5.
– When completed, touch [Basic] tab to return to the Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-16 bizhub 500/420/360 (Phase 3)
4Touch [Finishing] on the Basic Screen.
The Finishing Screen will be displayed.
5Select the staple position.
– To staple at a corner, touch [Corner] to highlight it.
– To staple along the edge, touch [2 Position] to highlight it.
6Select staple position.
– Touch [Position] to display the Staple Position popup menu.
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-17– Touch the desired key to highlight it.
7Touch [OK] twice.
The Basic Screen will be restored.
8Specify any necessary copy settings.
9Press [Start].
The scan/print job will start.
2
Reminder 
Finisher FS-510 trays gradually go up/down while printed materials 
output, depending on the tray selected.With Saddle stitcher SD-502 or 
Mailbin kit MT-501, the operation of the trays become greater. DO NOT 
allow any object to interfere with the operation of the tray around the 
finisher, as any interference may cause damage to the finisher.
Finisher FS-511 tray 2 (main tray) gradually goes down while printed 
materials output. DO NOT allow any object to interfere with the operation 
of the tray 2 (main tray) on the left side of the finisher, as any interference 
may cause damage to the finisher.
2
Note 
To cancel changes to the settings, touch [Cancel] on the Finishing 
Screen.
To cancel all settings, press [Reset].
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-18 bizhub 500/420/360 (Phase 3)
7.4 Punching File Holes in Copies (Punch)
The Punch mode is available on the machine with Finisher FS-511 installed, 
or if Finisher FS-510 mounted with Punch Unit PU-501 option is installed.
2
Note 
Finisher FS-510 is initially equipped with two exit trays, and one optional 
exit tray (OT-601) can be installed. Contact your service representative, if 
desired. (Already installed in the above illustration.)
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-19Function overview
The Original Direction setting for the samples below is supposed to be the 
one which the top of the original is aligned to the rear side of the machine.
KeySample
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-20 bizhub 500/420/360 (Phase 3)To copy using Punch mode
0If Punch is to be selected, select the orientation in which the original is 
positioned and the orientation of the page to be punched, otherwise the 
copies may not be punched as desired.
0This mode is available in combination with Group, Sort + Offset, Group + 
Offset, or Staple mode.
0If punch position setting is different from the binding position specified in 
Page Margin of Application setting, the punch position is given priority.
0With Auto selected on the Punch Position popup menu, the punch 
position will be determined automatically to the longer side for A4 copy 
paper, or to the shorter side for copy paper larger than A4.
0Be sure that the side guide plates of the paper tray are securely aligned 
to the paper; otherwise the copies may not be punched in position.
0Available paper weight for Punch Unit PU-501 mounted on Finisher FS-
510 is 56 to 90 gm
2, while paper weight for Finisher FS-511 is 60 to 90 
gm2. For details of other specifications, see Paper Weight on 
page 10-4.
0If the ATS (Automatic Tray Switching) functions while the machine uses 
the Punch mode, the punch holes may be slightly off the appropriate 
positions.
0Do not punch special paper type such as overhead projection 
transparent films, labels, etc.Otherwise, machine trouble may occur.
0Each output tray of Finisher FS-510 and FS-511 has a limit in capacity. 
Be careful not to exceed the limit. For details, see Paper Tray/ Output 
Tray Capacity on page 10-5.
Downloaded From ManualsPrinter.com Manuals