Konica Minolta bizhub 420 User Manual

							Utility 16
bizhub 500/420/360 (Phase 3) 16-89
3Select the desired priority mode in the left side area of the screen. 
Touch [Copy], [Scan], or [Fax] to highlight it.
In the right side area of the screen, specify the period of time before 
System Auto Reset is activated. Select the desired time from 1 to 9 
minutes.
When touching [OFF] to highlight it, System Auto Reset is not 
activated.
4Touch [OK] to complete the setting.
– To cancel the change, touch [Cancel].
In either case, the Reset Setting Screen will be restored.
5If further changes are required, touch the desired key.
2
Note 
With OFF selected for System Auto Reset function, the Enlarge Display 
mode will not be released, while User Authentication/ Account Track 
function will be cancelled in one minute.
Downloaded From ManualsPrinter.com Manuals 
						

							16Utility 
16-90 bizhub 500/420/360 (Phase 3)9 Reset Setting > 2 Auto Reset
Auto Reset is the function to automatically restore the copier/scanner 
settings specified as initial setting when the specified period of time has 
elapsed without any operation on the touch panel or control panel made.
Use this setting mode to specify the period of time to be elapsed before Auto 
Reset is activated.
According to the factory default, the machine will activate Auto Reset in one 
minute.
Downloaded From ManualsPrinter.com Manuals 
						

							Utility 16
bizhub 500/420/360 (Phase 3) 16-91
1Follow the procedure described in How to access the Administrator 
Setting Screen on page 16-3 to display the Administrator Setting 
Screen.
2Touch [1 System Setting], [9 Reset Setting], and then [2 Auto Reset].
The Auto Reset Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							16Utility 
16-92 bizhub 500/420/360 (Phase 3)
3Touch [Input] in each area of Copy, Scan, and Fax, then use the control 
panel keypad to enter the desired period of time to be elapsed before 
Auto Reset is activated.
When touching [OFF] to highlight it, Auto Reset for each is not 
activated.
4Touch [OK] to complete the setting.
– To cancel the change, touch [Cancel].
In either case, the Reset Setting Screen will be restored.
5If further changes are required, touch the desired key.
Downloaded From ManualsPrinter.com Manuals 
						

							Utility 16
bizhub 500/420/360 (Phase 3) 16-939 Reset Setting > 3 Job Reset
Select whether or not to initialize the settings currently specified when the 
machine takes it that the user has changed or original document is loaded 
into the ADF.
Also, select the copy condition to be initialized each time a single job has 
been completed. The following settings are provided.
Staple Setting: Initializes specified conditions in Staple mode.
Original Set Bind Direction: Initializes specified conditions in Original 
Direction and Margin.
Reset Data After Job: Initializes all copy conditions specified for the 
completed job.
2
Note 
This machine considers the following cases as user change (When 
Account is Changed):
- When the optional key counter or magnetic card of the data controller 
is removed.
- When [Access] is pressed after the User Authentication/ Account Track 
setting has once been performed.
Downloaded From ManualsPrinter.com Manuals 
						

							16Utility 
16-94 bizhub 500/420/360 (Phase 3)
1Follow the procedure described in How to access the Administrator 
Setting Screen on page 16-3 to display the Administrator Setting 
Screen.
2Touch [1 System Setting], [9 Reset Setting], and then [3 Job Reset].
The Job Reset Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Utility 16
bizhub 500/420/360 (Phase 3) 16-95
3Specify the reset setting for account change.
– Touch [When Account is changed] to display the setting menu on 
the right side of the screen.
– Select [Reset] to initialize the current settings and to clear the 
current account and password when key counter is removed.
4Specify the reset setting for original change.
Select whether or not to initialize the previous job settings when 
original document is loaded into the ADF.
– Touch [When Original is set on ADF] to display the setting menu on 
the right side of the screen.
– Select [Reset] to initialize the previous job settings when original is 
loaded into the ADF. Copy settings are to be made each time the 
original document is loaded into the ADF.
Downloaded From ManualsPrinter.com Manuals 
						

							16Utility 
16-96 bizhub 500/420/360 (Phase 3)
5Specify the setting for job change.
Select whether or not to release the Staple Setting and Original 
Set/Bind Direction, and to reset all the setting data after completion of 
each job.
– Touch [When NEXT JOB is selected] to display the Next Job 
Screen.
– Touch the key to be specified. The setting menu will be displayed 
on the right side of the screen.
Select either [ON] or [OFF] for each.
6If further changes are required, touch the desired key.
Downloaded From ManualsPrinter.com Manuals 
						

							Utility 16
bizhub 500/420/360 (Phase 3) 16-979 Reset Setting>4 System Auto Reset of Proof Copy
Select whether or not to initialize the settings currently specified when a job 
is stopped for proof copying.
1Follow the procedure described in How to access the Administrator 
Setting Screen on page 16-3 to display the Administrator Setting 
Screen.
2Touch [1 System Setting], [9 Reset Setting], and then [4 System Auto 
Reset of Proof Copy].
The System Auto Reset of Proof Copy Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							16Utility 
16-98 bizhub 500/420/360 (Phase 3)
3Select either [ON] or [OFF].
4Touch [OK] to complete the setting.
– To cancel the change, touch [Cancel].
In either case, the Reset Setting Screen will be restored.
5If further changes are required, touch the desired key.
Downloaded From ManualsPrinter.com Manuals