Konica Minolta bizhub 420 User Manual

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-21
1Position the original to be copied.
2Using the keypad, enter the desired number of copies.
3Touch [Combine Originals] tab on the Basic Screen, then make Original 
Direction and Margin settings.
– For setting Original Direction, see Specifying Orientation of 
Original (Original Direction) on page 5-14.
For setting Margin, see Specifying Position of Binding Margin 
(Margin) on page 5-18.
– When completed, touch [Basic] tab to return to the Basic Screen.
4Touch [Finishing] on the Basic Screen.
The Finishing Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-22 bizhub 500/420/360 (Phase 3)
5Touch [4 holes] to highlight it.
– Group and Offset are also available in combination. Touch the 
desired key to highlight it.
– To cancel the setting, touch the button again to deselect it.
6Select the punch position.
– Touch [Position] to display the Punch Position popup menu.
– Touch the desired key to highlight it.
7Touch [OK] twice.
The Basic Screen will be restored.
8Specify any necessary copy settings.
9Press [Start].
The scan/print job will start.
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-23
2
Reminder 
Finisher FS-510 trays gradually go up/down while printed materials 
output, depending on the tray selected.With Saddle Stitcher SD-502 or 
Mailbin Kit MT-501, the operation of the trays become greater. DO NOT 
allow any object to interfere with the operation of the tray around the 
finisher, as any interference may cause damage to the finisher.
Finisher FS-511 tray 2 (main tray) gradually goes down while printed 
materials output. DO NOT allow any object to interfere with the operation 
of the tray 2 (main tray) on the left side of the finisher, as any interference 
may cause damage to the finisher.
2
Note 
To cancel changes to the settings, touch [Cancel] on the Finishing 
Screen.
To cancel all settings, press [Reset].
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-24 bizhub 500/420/360 (Phase 3)
7.5 Folding Copies at the Center/Binding Copies at the 
Center: Half Fold/ Fold & Staple
The Half Fold and Fold & Staple modes are 
available on the machine mounted with 
Finisher FS-510 and Saddle Stitcher 
SD-502 as illustrated on the right, along 
with Booklet function which will be 
automatically selected in combination.
-In the Half Fold mode, each copied sheet is creased and output to the 
Saddle stitcher tray.
-In the Fold & Staple mode, each copied set is creased and stapled at two 
positions (saddle stitched), then output to the Saddle stitcher tray.
2
Note 
Finisher FS-510 is initially equipped with two exit trays, and one optional 
exit tray (OT-601) can be installed. Contact your service representative, if 
desired. (Already installed in the above illustration.)
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-25Function overview
KeyDescription
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-26 bizhub 500/420/360 (Phase 3)To copy using Half Fold or Fold & Staple
0As the default setting, 1%2 mode and Booklet function will be specified 
automatically when Half Fold or Fold & Staple is selected. For details, see 
Making Multiple Page Signature Booklet (Booklet) on page 6-69.
Half Fold and Fold & Staple are still available even if 1%2 mode is 
changed or Booklet function is cancelled.
0Auto Zoom is automatically selected. Half Fold and Fold & Staple are still 
available even if Auto Zoom is deselected manually.
0Staple position: 2 staples in the center (saddle stitch), pitch 120 mm +/– 
4 mm (staple width 11 mm)
Max. number of sheets in Fold & Staple mode: 15 sheets (80gm
2 paper)
0Paper size:A3 w, B4 w, A4 w, B5 w 
Paper weight: 60 to 90gm
2
For details of other specifications, see Paper Weight on page 10-4.
0Saddle stitcher tray capacity: 200 sheets or 20 sets (80gm2 paper)
Using Half Fold or Fold & Staple mode, finished sets are delivered only to 
the Saddle stitcher tray.
1Position the original to be copied.
– When using Fold & Staple mode, be sure that the original count 
does not exceed the maximum number of sheets specified for Fold 
& Staple mode.
2Using the keypad, enter the desired number of copies.
– Be sure that the output sheets may not exceed the Saddle stitcher 
tray capacity.
3Touch [Folding] on the Basic Screen.
The Folding Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-27
4Touch [Half Fold] or [Fold & Staple] to highlight it.
5Touch [OK].
The Basic Screen will be restored.
6Specify any necessary copy settings.
7Press [Start].
The scan/print job will start.
2
Reminder 
Finisher FS-510 trays gradually go up/down while printed materials 
output, depending on the tray selected.With Saddle stitcher SD-502 or 
Mailbin kit MT-501, the operation of the trays become greater. DO NOT 
allow any object to interfere with the operation of the tray around the 
finisher, as any interference may cause damage to the finisher.
2
Note 
To cancel changes to the settings, touch [Cancel] on the Finishing 
Screen.
To cancel all settings, press [Reset].
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-28 bizhub 500/420/360 (Phase 3)
7.6 Output for Machine with Separator
The machine with Separator installed can 
deliver the printed sheets separately into 
different trays.
The following four output modes are 
available for use with two output trays. As 
factory default, copies will be delivered 
into the tray 2 in Group mode.
-Sort
Select this setting to separate each set of a multi-page original.
-Group
Select this setting to separate the copies of each page in a multi-page 
original.
-Sort + Offset
Select this setting to rotate every other set by 90° upon exit, provided the 
same paper size is loaded in two trays, one tray with paper loaded in 
crosswise orientation v and the other tray with paper loaded in 
lengthwise orientation w, e.g., A4- or B5-size paper. 
-Group + Offset
Select this setting to rotate every other grouped set by 90° upon exit, 
provided the same paper size is loaded in two trays, one tray with paper 
loaded in crosswise orientation v and the other tray with paper loaded in 
lengthwise orientation w, e.g., A4- or B5-size paper. 
Specifying a tray for the output to be made in other job type than Copy (e.g. 
Print, Reports, or Fax), printed sheets will be distributed into the specified 
tray in order to prevent the output sheets from being mixed up.
2
Note 
The output tray can be specified for each job type (Copy, Print, and 
Reports). See 2 Output Setting>2 Output Tray Setting on page 16-39 
for details.
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing/Folding7
bizhub 500/420/360 (Phase 3) 7-29To specify Separator output mode
0As the default setting, Sort is selected. No limit is established in Sort 
mode.
0Some copy conditions are incompatible with Group mode. For details, 
see Copy Conditions Incompatible with Finishing/Folding on 
page 7-32.
0If no finisher is installed and the following conditions are met, printed 
copies can be fed out and sorted in an alternating crisscross pattern.
A4- or B5-size paper is used.
Paper of the same size and type is loaded with the crosswise orientation 
v in one paper tray and with the lengthwise orientation w in other tray.
Auto Paper Select setting is selected.
The Auto Zoom setting is used when the Mixed Original setting is 
selected.
0The tray 1 (upper tray) capacity is max. 100 sheets, and tray 2 (lower tray) 
capacity is max. 250 sheets. If a copy run of more than those limits is 
required, be sure to remove the copies from the tray before the maximum 
capacity is reached.
1Position the original to be copied.
2Using the keypad, enter the desired number of copies.
3Load the desired copy paper size in a tray.
– When using an alternating crisscross pattern, load A4- or B5-size 
paper with portrait orientation v in one paper tray and with the 
landscape orientation w in other tray.
4Touch [Finishing] on the Basic Screen.
The Finishing Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							7Finishing/Folding
7-30 bizhub 500/420/360 (Phase 3)
5Select Sort or Group, and set Offset to use offset output.
– To set Sort mode, touch [Sort] to highlight it.
– To set Group mode, touch [Group] to highlight it.
– To set Sort in alternating crisscross pattern, touch [Sort] and 
[Offset] to highlight them.
– To set Group in alternating crisscross pattern, touch [Group] and 
[Offset] to highlight them.
6Select the desired output tray.
– Touch [Tray 1] or [Tray 2] to highlight it.
7Touch [OK].
The Basic Screen will be restored.
Downloaded From ManualsPrinter.com Manuals