Konica Minolta bizhub 420 User Manual

							Installation and Operation Precautions2
bizhub 500/420/360 (Phase 3) 2-13For Users in countries not subject to Class B regulations
7 WARNING
Interference with radio communications.
%This is a Class A product. In a domestic environment this product may 
cause radio interference in which case the user may be required to take 
adequate measures.
%This device must be used with a shielded network (10 Base-T/100 
Base-TX) cable and a shielded parallel cable. The use of non-shielded 
cables is likely to result in interference with radio communications and 
is prohibited under CISPR rules and local rules.
Laser Safety
This product employs a Class 3B laser diode having maximum power of 
10 mW and wavelength of 775 - 800 nm.
This product is certified as a Class 1 laser product. Since the laser beam is 
concealed by protective housings, the product does not emit hazardous 
laser radiation as long as the product is operated according to the 
instructions in this manual.
For Denmark users
7 ADVARSEL
Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af 
funktion.
%Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af 
funktion. Undgå udsættelse for stråling. Klasse 1 laser produkt der 
opfylder IEC 60825-1 sikkerheds kravene.
Dette er en halvlederlaser. Laserdiodens højeste styrke er 10 mW og 
bølgelængden er 775-800 nm.
Downloaded From ManualsPrinter.com Manuals 
						

							2Installation and Operation Precautions
2-14 bizhub 500/420/360 (Phase 3)For Norway users
7 ADVARSEL!
Dette en halvleder laser.
%Dersom apparatet brukes på annen måte enn spesifisert i denne 
bruksanvisning, kan brukeren utsettes for unsynlig laserstråling som 
overskrider grensen for laser klass 1.
Dette en halvleder laser. Maksimal effekt till laserdiode er 10 mW og 
bølgelengde er 775-800 nm.
For Finland, Sweden users
LOUKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
7 VAROITUS
Tämä on puolijohdelaser.
%Laitteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla 
tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle 
näkymättömälle lasersäteilylle.
Tämä on puolijohdelaser. Laserdiodin sunrin teho on 10 mW ja aallonpituus 
on 775-800 nm.
7 VARNING
Det här är en halvledarlaser.
%Om apparaten används på annat sätt än i denna bruksanvisning 
specificerats, kan användaren utsättas för osynlig laserstrålning, som 
överskrider gränsen för laserklass 1.
Det här är en halvledarlaser. Den maximala effekten för laserdioden är 10 mW 
och våglängden är 775-800 nm.
Downloaded From ManualsPrinter.com Manuals 
						

							Installation and Operation Precautions2
bizhub 500/420/360 (Phase 3) 2-15
7 VAROITUS
Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle 
lasersäteilylle.
%Älä katso säteeseen.
7 VARNING
Osynlig laserstrålning när denna del är öppnad och spärren är 
urkopplad.
%Betrakta ej strålen.
Downloaded From ManualsPrinter.com Manuals 
						

							2Installation and Operation Precautions
2-16 bizhub 500/420/360 (Phase 3)Ozone Release
7 CAUTION 
Locate the Machine in a Well Ventilated Room
%A negligible amount of ozone is generated during normal operation of 
this machine. An unpleasant odor may, however, be created in poorly 
ventilated rooms during extensive machine operations. For a 
comfortable, healthy, and safe operating environment, it is 
recommended that the room well ventilated.
7 ATTENTION 
Placer l’appareil dans une pièce largement ventilée.
%Une quantité d’ozone négligable est dégagée pendant le 
fonctionnement de l’appareil quand celui-ci est utilisé 
normalement.Cependant, une odeur désagréable peut être ressentie 
dans les pièces dont l’aération est insuffisante et lorsque une utilisation 
prolongée de l’appareil est effectuée. Pour avoir la certitude de 
travailler dans un environnement réunissant des conditions de confort, 
santé et de sécurité, il est préférable de bien aérer la pièce ou se trouve 
l’appareil.
Acoustic noise (For European Users Only)
Maschinenlärminformations-Verordnung 3. GPSGV: Der höchste 
Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779.
Downloaded From ManualsPrinter.com Manuals 
						

							Installation and Operation Precautions2
bizhub 500/420/360 (Phase 3) 2-17
2.3 Caution Notations and Labels
Safety precaution notations and labels appear on this machine at the 
following positions.
Be very careful that an accident does not occur when operations such as 
removing paper misfeeds are performed.
The fixing unit is very hot.
To avoid getting burned DO 
NOT TOUCH.
CAUTION
This area generates 
high voltage.  If 
touched, electrical 
shock may occur. DO 
NOT TOUCH!
CAUTION
The area opened by the 
conveyance lever is very hot.
To avoid getting burned DO 
NOT TOUCH.
CAUTION
Finisher FS-510
Downloaded From ManualsPrinter.com Manuals 
						

							2Installation and Operation Precautions
2-18 bizhub 500/420/360 (Phase 3)
CAUTION
This area is very hot.
To avoid getting 
burned DO NOT 
TOUCH.
To avoid injury, DO NOT put 
your hand on the top of the 
printed sheets. Be sure to 
hold both sides of the 
printed sheets when 
removing them, and DO NOT 
leave your hand on the 
printed sheets while the tray 
2 (primary tray) goes up.
CAUTION
Finisher FS-511
Downloaded From ManualsPrinter.com Manuals 
						

							Installation and Operation Precautions2
bizhub 500/420/360 (Phase 3) 2-19
2.4 Space Requirements
To ensure that machine operation, consumables replenishing, part 
replacement, and regular maintenance can easily be performed, adhere to 
the recommended space requirements detailed below.
bizhub 500/420/360 + DK-501
bizhub 500/420/360 + PC-202 + FS-510Unit : mm Unit : mm
Downloaded From ManualsPrinter.com Manuals 
						

							2Installation and Operation Precautions
2-20 bizhub 500/420/360 (Phase 3)
bizhub 500/420/360 + PC-402 + FS-511 + LU-201 bizhub 500/420/360 + PC-202 + FS-510 + MT-501 + LU-201bizhub 500/420/360 + PC-202 + FS-510 + SD-502 + LU-201Unit : mm
Unit : mm
Unit : mm
Downloaded From ManualsPrinter.com Manuals 
						

							Installation and Operation Precautions2
bizhub 500/420/360 (Phase 3) 2-21
2
Reminder 
Be sure to allow a clearance of 200 mm (7-3/4 in.) or more at the back of 
this machine for the ventilation duct.
Downloaded From ManualsPrinter.com Manuals 
						

							2Installation and Operation Precautions
2-22 bizhub 500/420/360 (Phase 3)
2.5 Operation Precautions
To ensure the optimum performance of this machine, observe the 
precautions described below.
Power Source
The power source requirements are as follows.
-Voltage: 220-240 V AC
-Frequency: 50 Hz
– Use a power source with as little voltage or frequency fluctuations as 
possible.
Operating Environment
The environmental requirements for correct operation of the machine are as 
follows.
-Operating temperature: 10°C (50°F) to 30°C (86°F)
-Humidity: 10% to 80% 
Storage of Copies
To store copies, follow the recommendation listed below.
-Copies that are to be kept for a long time should be kept where they are 
not exposed to light in order to prevent them from fading.
-Adhesive that contains solvent (e.g., spray glue) may dissolve the toner 
on copies.
Downloaded From ManualsPrinter.com Manuals