Konica Minolta bizhub 420 User Manual

							Advanced Information8
bizhub 500/420/360 (Phase 3) 8-35The Message Display Time Screen will be displayed.
3Select the desired display time.
– Touch [3 sec.] or [5 sec.] to highlight it.
4Touch [OK].
The Accessibility Setting Screen will be restored.
5Touch [Close], or press [Accessibility] on the control panel.
The Basic Screen will be restored.
2
Note 
Touch [Cancel] on the Message Display Time Screen to cancel the setting 
change.
Downloaded From ManualsPrinter.com Manuals 
						

							8Advanced Information
8-36 bizhub 500/420/360 (Phase 3)Enabling Key Tones (Sound Setting)
Specify the sound of the machine.
-Key Accept Sound/Key Refuse Sound
Specify whether or not to enable the key tone for the control/touch panel 
keys.
-Warning Sound
Specify whether or not to enable the warning sound when the machine 
stops due to paper jam or empty tray etc., and also specify the sound 
duration from 2 seconds, 5 seconds, and 10 seconds.
0Key Accept Sound/Key Refuse Sound, is enabled (ON) as factory default.
0Warning Sound is enabled (ON) and Warning Sound Times is set to 
3.0sec as factory default.
1Press [Accessibility] on the control 
panel.
The Accessibility Setting Screen will 
be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Advanced Information8
bizhub 500/420/360 (Phase 3) 8-37
2Touch [4 Sound Setting], or press [4] on the control panel keypad.
The Sound Setting Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							8Advanced Information
8-38 bizhub 500/420/360 (Phase 3)
3Select whether or not to enable key tones.
– Touch [1 Key Accept Sound/ Key Refuse Sound], or press [1] on the 
– The Key Accept Sound/ Key Refuse Sound Screen will be 
displayed.
– Touch [ON] to activate, or [OFF] to deactivate.
– Touch [OK] to return to the Sound Setting Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Advanced Information8
bizhub 500/420/360 (Phase 3) 8-39
4Select whether or not to enable warning sound.
– Touch [2 Warning Sound], or press [2] on the control panel keypad.
– The Warning Sound Screen Will be displayed.
– Touch [ON] to activate, or [OFF] to deactivate.
When selecting [ON], select one from [3 sec.], [5 sec.], or [10 sec].
– Touch [OK] to return to the Sound Setting Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							8Advanced Information
8-40 bizhub 500/420/360 (Phase 3)
5Touch [Close].
The Accessibility Setting Screen will be restored.
6Touch [Close], or press [Accessibility] on the control panel.
The Basic Screen will be restored.
2
Note 
Touch [Cancel] on the Key Accept Sound Screen to cancel the setting 
change.
Downloaded From ManualsPrinter.com Manuals 
						

							Advanced Information8
bizhub 500/420/360 (Phase 3) 8-41Adjusting the Position of Touch Sensor (Touch Panel Adjustment)
If touch panel keys do not respond correctly, the touch sensor may shift in 
position of the touch keys.
In this case, use this function to adjust the position of touch sensor.
1Press [Accessibility] on the control 
panel.
The Accessibility Setting Screen will 
be displayed.
2Touch [5 Touch Panel Adj.], or press [5] on the control panel keypad.
– If the [5 Touch Panel Adj.] key does not function, use the control 
panel keypad to select it.
The Touch Panel Adjustment Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							8Advanced Information
8-42 bizhub 500/420/360 (Phase 3)
3Touch the four check keys [+] to check the buzzer tone.
When a check point is touched correctly, the Start LED on the control 
panel will light up in green.
?Is there a specific order to touch the check keys?
%No. Touch them in any order.
?Why can no buzzer tone be heard?
No sound can be heard if the Sound Setting has been set to OFF.
%Set the function to ON. For details, see Enabling Key Tones 
(Sound Setting) on page 8-36.
?Do you want to reset the adjustment?
%Press [C] (Clear) on the control panel, then touch the four check 
keys [+] again.
?Do you want to cancel the adjustment?
%Press [Stop] on the control panel. The Basic Screen will be 
restored.
4Press [Start] on the control panel.
The position of the touch sensor will be adjusted, and the Accessibility 
Screen will be restored.
Downloaded From ManualsPrinter.com Manuals 
						

							Advanced Information8
bizhub 500/420/360 (Phase 3) 8-43
5Touch [Close], or press [Accessibility] on the control panel.
The Basic Screen will be restored.
2
Note 
Contact your service representative if adjustment result is not 
satisfactory.
Downloaded From ManualsPrinter.com Manuals 
						

							8Advanced Information
8-44 bizhub 500/420/360 (Phase 3)Setting Auto Reset Notification (Auto Reset Notification)
When the automatic panel reset operation is performed, a message can be 
displayed, requesting confirmation to reset the settings in Enlarge Display 
mode.
In addition, it is possible to specify when the message is displayed, 
requesting confirmation to reset the settings in Enlarge Display mode.
0The Enlarge Display Auto Reset Notification Screen will not be displayed 
as factory default.
0Even if the machine is set to display the Enlarge Display Auto Reset 
Notification Screen, the Enlarge Display Confirmation Screen will be 
displayed when the same period of time is specified to activate Auto 
Reset and System Auto Reset.
0The factory default setting is OFF.
1Press [Accessibility] on the control 
panel.
The Accessibility Setting Screen will 
be displayed.
Downloaded From ManualsPrinter.com Manuals