Konica Minolta bizhub 420 User Manual

							Supplies & Handling11
bizhub 500/420/360 (Phase 3) 11-7
3Withdraw and pull up the used toner 
cartridge to remove it.
4Loosen toner by tapping bottom of 
the new toner cartridge on a solid 
surface at least five times.
– Remove the new toner cartridge 
form the box.
– The toner within the toner 
cartridge may have become 
compacted. Be sure to handle 
steps 4 to 6 until the toner is 
mostly broken up before 
installing the cartridge.
5Loosen toner by tapping top of the 
new toner cartridge on a solid 
surface at least five times.
6Shake the new toner cartridge by 
turning it over about five times.
Downloaded From ManualsPrinter.com Manuals 
						

							11Supplies & Handling
11-8 bizhub 500/420/360 (Phase 3)
7Remove the cap from the new toner 
cartridge.
8Set the toner cartridge from its top 
first, making sure that it is correctly 
oriented.
– Be sure the Up arrow mark on 
the toner cartridge is shown on 
the top; otherwise the toner 
cartridge cannot be set properly.
9Return the cartridge holder to its 
original position
10Close and lock the toner cartridge 
cover, then close the machine front 
door.
Downloaded From ManualsPrinter.com Manuals 
						

							Supplies & Handling11
bizhub 500/420/360 (Phase 3) 11-9
11.3 Adding Staples
When the staple cartridge of the Finisher FS-511 is empty, the Basic Screen 
displays the following message in the message area.
To replace the staple cartridge for Finisher FS-511, see To replace the 
staple cartridge for Finisher FS-511 on page 11-11.
When the staple cartridge of the Finisher FS-510 is empty, the Basic Screen 
displays the following message in the message area.
To replace the staple cartridge for Finisher FS-510, see To replace the 
staple cartridge for Finisher FS-510 on page 11-14.
Downloaded From ManualsPrinter.com Manuals 
						

							11Supplies & Handling
11-10 bizhub 500/420/360 (Phase 3)When either of the two staple cartridges becomes empty in the Saddle 
stitcher SD-502 mounted on Finisher FS-510, the Basic Screen displays the 
following message in the message area.
For details on replacing the staple cartridge for Saddle stitcher SD-502, see 
To replace the staple cartridge for Saddle stitcher SD-502 on page 11-18.
2
Reminder 
Be sure to replace the staple cartridge only after the message is 
displayed, otherwise the machine may be damaged.
Display in Enlarge Display Mode
When the staple cartridge is empty, the following screen is displayed in 
enlarge display mode.
Downloaded From ManualsPrinter.com Manuals 
						

							Supplies & Handling11
bizhub 500/420/360 (Phase 3) 11-11To replace the staple cartridge for Finisher FS-511
0Be sure to replace the staple cartridge after displaying the message, 
otherwise the machine may be damaged.
1Slide the finisher to the left.
– Holding the finisher handle on the 
top, slide the finisher to the left 
until it stops.
2Open the finisher right door FN7.
3Turn the dial to the left until the two 
staplers come to the center.
4Pull up then forward the staple 
holder to remove it from the stapler.
– Please check the message which 
stapler to remove.
Staple cartridge 1: rear side
Staple cartridge 2: front side
Downloaded From ManualsPrinter.com Manuals 
						

							11Supplies & Handling
11-12 bizhub 500/420/360 (Phase 3)
5Remove the empty staple cartridge.
– Push the two PUSH buttons of 
the staple holder to slide the top 
cover upward, then remove the 
empty staple cartridge.
6Install the new staple cartridge into 
the staple cartridge.
– Push the staple cartridge, and 
then check that the cartridge is 
securely installed.
7Push down the top cover to return it 
to its original position.
8Remove the lock tape from the 
cartridge.
1
2
Downloaded From ManualsPrinter.com Manuals 
						

							Supplies & Handling11
bizhub 500/420/360 (Phase 3) 11-13
9Return the staple holder to the 
stapler, and push it down until it 
clicks in place.
10Close the finisher right door FN7.
11Close the finisher right side door, 
then slide the finisher to the right to 
return it to its original position.
Downloaded From ManualsPrinter.com Manuals 
						

							11Supplies & Handling
11-14 bizhub 500/420/360 (Phase 3)To replace the staple cartridge for Finisher FS-510
0Be sure to replace the staple cartridge after displaying the message, 
otherwise the machine may be dameged.
0When replacing the staple cartridge, touch [Add Staples] to move the 
stapler toward the finisher front door. If necessary, turn the stapler 
moving knob to bring the stapler forward.
1Touch [Finishing] on the Basic Screen.
The Finishing Screen will be displayed. The [Add Staples] key will 
appear on the Finishing Screen.
2Touch [Add Staples].
The Moving Stapler Screen will be displayed while the stapler deeply 
positioned inside the finisher moves toward the finisher front door.
When moving toward completely, the Check Stapler Screen will be 
displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Supplies & Handling11
bizhub 500/420/360 (Phase 3) 11-15
3When the Check Stapler Screen is displayed, open the finisher front 
door.
– Moving Stapler Screen
DO NOT open the finisher door while the Moving Stapler Screen is 
displayed.
– Check Stapler Screen
4Remove the stapler holder from the 
stapler.
1
2
Downloaded From ManualsPrinter.com Manuals 
						

							11Supplies & Handling
11-16 bizhub 500/420/360 (Phase 3)
5Remove the empty staple cartridge from the staple cartridge holder.
– Push the two PUSH buttons of 
the staple holder to slide the top 
cover upward, then remove the 
empty staple cartridge.
6Install the new staple cartridge into the staple cartridge.
– Firmly insert the new cartridge 
into staple holder.
7Push down the top cover to return it 
to its original position.
8Remove the lock tape from the 
cartridge.
1
2
Downloaded From ManualsPrinter.com Manuals