Konica Minolta bizhub 420 User Manual

							Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-63
7Touch [OK].
The Basic Screen will be restored.
8Select additional copy conditions, as desired.
– For details on specifying the binding margin for double-sided 
copies, see Creating Margin of Copy Image (Page Margin) on 
page 6-76.
9Press [Start] on the control panel.
The original image will be scanned into memory.
When completed, the message Scanning stopped./ Press [Start] to 
continue. will be displayed in the message area.
10Replace the original on the original glass with the second page 
(page 2), then press [Start].
– Repeat this step for all original pages to be scanned.
11When all the original pages are scanned, touch [Finish].
Downloaded From ManualsPrinter.com Manuals 
						

							4Basic Copy Operations
4-64 bizhub 500/420/360 (Phase 3)
12Press [Start].
All the data in memory will be output to make double-sided copies.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
2
Note 
Using the original glass to scan the double-sided original, it does not 
matter which of the two duplex modes (1%2 or 2%2) is specified.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-65To make single-sided copies from double-sided original
Follow the procedure below to make single-sided copies from double-sided 
original using the ADF.
When using the original glass to scan the double-sided original, select 1%1 
mode.
0Specify the Original Direction according to the orientation of the original 
loaded in the ADF. For details, see Specifying Orientation of Original 
(Original Direction) on page 5-14.
0The desired copy result may not be obtained from the following types of 
double-sided original unless the original page margin is specified 
manually.
A4 or smaller portrait-type original with top margin created
A4 or smaller landscape-type original with right/left margin created
B4 or larger portrait-type original with right/left margin created
B4 or larger landscape-type original with top margin created.
1Position the original in the ADF.
Downloaded From ManualsPrinter.com Manuals 
						

							4Basic Copy Operations
4-66 bizhub 500/420/360 (Phase 3)
2Touch [Simplex/Duplex] on the Basic Screen.
The Simplex/Duplex Screen will be displayed.
3Touch [2%1] to highlight it.
4Specify the original set direction according to the orientation of 
positioned original.
– Touch [Original Direction] to display the Original Direction Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-67– Select one of the original direction key according to the orientation 
of positioned original, then touch [OK].
5Specify the binding direction of original.
–With [2%2] selected, the binding direction of original should be 
specified manually, otherwise the desired copy result may not be 
obtained.
– Touch [Binding Direction] to display the Binding Direction Screen.
– Touch the desired key, then touch [OK].
Downloaded From ManualsPrinter.com Manuals 
						

							4Basic Copy Operations
4-68 bizhub 500/420/360 (Phase 3)
6Touch [OK].
The Basic Screen will be restored.
7Select additional copy conditions, as desired.
– For details on specifying the binding margin of double-sided 
original, see Specifying Position of Binding Margin (Margin) on 
page 5-18.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-69
4.9 Separate Scan Setting
A large amount of the original can be divided and scanned into memory.
The ADF accepts only 80 original sheets at a time, however, the Separate 
Scan setting allows you to handle the original that exceeds 80 sheets as a 
single job.
The multiple original scanned from the original glass, or both from the ADF 
and original glass, can also be combined into a single job.
To use Separate Scan mode
0Note that the maximum number of the original available in the ADF does 
not change in this mode.
Do not load more than 80 original sheets or above the limit mark, 
otherwise paper misfeed or damage to the original may be caused.
0Separate Scan mode is necessarily used and operates automatically in 
the following functions:
Making double-sided copies using original glass
Image Insert
Book Copy
1Position the original.
– When using the original glass, 
place the first page face down on 
the original glass.
– When using the ADF, load the 
original arranged in page order 
with page one on the top.
Downloaded From ManualsPrinter.com Manuals 
						

							4Basic Copy Operations
4-70 bizhub 500/420/360 (Phase 3)
2Touch [Separate Scan] on the Basic Screen.
3Select additional copy conditions, as desired.
4Press [Start] on the control panel.
The machine starts to scan the 
original.
The original image will be scanned into memory.
When completed, the message Scanning stopped./ Press [Start] to 
continue. will be displayed in the message area.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-71
5Replace the original, then press [Start].
– Repeat steps 4 and 5 for all 
original pages to be scanned.
6When all the original pages are scanned, touch [Finish]
7Press [Start] on the control panel.
All the data in memory will be output.
Downloaded From ManualsPrinter.com Manuals 
						

							4Basic Copy Operations
4-72 bizhub 500/420/360 (Phase 3)
!
Detail 
To delete the scanned image data, press [Stop]. For details, see To 
Stop/Resume/Delete a Job on page 4-78.
2
Note 
The memory indicator in the upper-right corner of the Basic Screen 
allows you to check the remainder of memory during the scanning job.
Downloaded From ManualsPrinter.com Manuals