Konica Minolta bizhub 420 User Manual

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-99
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
2
Reminder 
Non-Image Area Erase function may not operate properly for dark 
original. In this case, check this function using the original with white 
background.
This function may also perform incorrectly if the lighting in the work place 
is directly over the original glass. In this case, consult your service 
representative about an appropriate place for installation.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-100 bizhub 500/420/360 (Phase 3)Disabling Rotation Function (No Rotate)
Follow the procedure below to turn off/on the Rotation function.
0Available paper size for Rotation: A4, B5, A5
0Available original size for Rotation: A3, B4, A4, B5, A5, B611 e 17, 
0Rotation is initially enabled as factory default.
0When [Reset] on the control panel is pressed or Auto Reset function 
operates on the machine, the Rotation function will be turned on 
automatically even if disabled by this procedure.
1Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
2Touch [Image Adjustment] on the Application Screen.
The Image Adjustment Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-101
3Touch [No Rotate] on the Image Adjustment Screen to highlight it.
The Rotation function is now turned off.
4Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Image Adjustment Screen to cancel the 
setting change.
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-102 bizhub 500/420/360 (Phase 3)
6.15 Printing Additional Information (Stamp/Overlay)
This function allows you to print onto output copies the desired type of 
date/time, page number for multiple pages, numbering for multiple sets, 
built-in stamp, watermark, scanned image, and image stored in HDD.
The following modes are provided.
-Date/Time
Specify a format and print position to print the date and time.
-Page #
Specify a format and print position to print page number from the 
specified number.
-Set Numbering
Print four-digit distribution number to fill the background of each copied 
set. 
-Built-in Stamp
Print the desired letter type selected from preset stamps such as 
URGENT, IMPORTANT, etc.
-Watermark
Print the desired letter type selected from preset watermarks in the center 
of printed page background.
-Image Overlay
Copies can be printed with the first image scanned overlapping images 
later scanned.
-Store Overlay
A previously scanned image can be stored on the HDD and recalled when 
needed to be printed overlapping a document.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-103Function overview
The following five modes are provided for the Stamp function. These are 
compatible with each other.
ModeDescription
Date/Time
Page #
Set Numbering
’06/1/23 1:23PM
P1
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-104 bizhub 500/420/360 (Phase 3)
Built-in Stamp
Watermark
Image Overlay
Store Overlay
ModeDescription
URGENT
CONFIDENTIAL
IMPORTANT
HDD
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-105Printing Date/Time (Date/Time)
0Available to print the date only, without being followed by the time.
0The desired print position can be selected from nine areas. If required, 
make fine adjustment of the selected position both in lengthwise and 
widthwise directions by entering a value from 0.1 mm to 50.0 mm in 0.1 
mm increments.
0Select to print the date/time either on the cover or on all pages.
1Position the original.
2Enter the desired print quantity from the control panel keypad.
3Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-106 bizhub 500/420/360 (Phase 3)
4Touch [Stamp/Overlay], then touch [Date/Time].
The Date/Time Screen will be displayed.
5Specify the date type, time type, and pages to print.
– Touch one of the five keys under Date Type to highlight it.
– Select either of the two time types under Time Type. If the time 
indication is not desired, touch [None] to highlight it.
– Touch either of the two keys under Pages to highlight it.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-107– To change or make fine adjustment on the print position currently 
specified as indicated on the Print Position key, proceed to the next 
step.
To complete this setting, proceed to step 8.
6Touch [Print Position] on the Date/Time Screen to specify the desired 
print position.
– Touch one of the nine Print Position keys to highlight it.
– If fine adjustment is not required, proceed to step 8.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-108 bizhub 500/420/360 (Phase 3)
7Touch [Change Adjustment] on the Print Position Screen to make a fine 
adjustment of the print position.
– Touch [Left] or [Right] under Left & Right Adjustment to highlight it. 
Use [+] and [–] to enter a fraction in 0.1 mm increments. Touch the 
bidirectional arrow key to move the cursor, then use [+], [–], or 
control panel keypad to enter whole number part of the desired 
value.
Similarly, touch [Top] or [Bottom] under Top & Bottom Adjustment 
to highlight it, then enter the desired value.
To deactivate these adjustment, touch [No Adj.] for each.
?Do you want to change the currently entered value using control 
panel keypad?
%Press [C] (Clear) on the control panel, then enter the correct value.
?What if the value just entered is out of available range?
%The Input Error message will be displayed. Press [C] (Clear) on the 
control panel, then reenter the correct value.
8Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Date/Time Screen, Print Position Screen, or 
Fine-Tune Screen to cancel the setting change.
9Select additional copy conditions, as desired.
10Press [Start] on the control panel.
The machine will start scanning the original, then printing when ready 
for output.
Downloaded From ManualsPrinter.com Manuals