Canon Maxify Mb5020 User Guide

							The Machine Cannot Be Powered On
Check1 Press the  ON button.
Check2
 Make sure that the power plug is securely plugged into the power cord
connector of the machine, then turn it back on.
Check3  Unplug the machine from the power supply, then plug the machine back in and
turn the machine back on after leaving it for at least 2 minutes.
If the problem is not resolved, contact the service center.
1001
 
						

							Cannot Connect to Computer with a USB Cable Properly
Printing or Scanning Speed Is Slow/Hi-Speed USB Connection Does
Not Work/"This device can perform faster" Message Is Displayed
If your system environment is not fully compatible with Hi-Speed USB, the machine will operate at a lower
speed provided under USB 1.1. In this case, the machine operates properly but printing or scanning
speed may slow down due to communication speed.
Check  Check the following to make sure that your system environment supports Hi-
Speed USB connection.
•
Does the USB port on your computer support Hi-Speed USB connection?
•
Does the USB cable or the USB hub support Hi-Speed USB connection?
Be sure to use a certified Hi-Speed USB cable. We recommend that the cable is no longer than around
10 feet / 3 meters.
•
Does the operating system of your computer support Hi-Speed USB connection?
Obtain and install the latest update for your computer.
•
Does the Hi-Speed USB driver operate properly?
Obtain the latest version of the Hi-Speed USB driver compatible with your hardware and reinstall it on
your computer.
Important
•
For details on Hi-Speed USB of your system environment, contact the manufacturer of your computer,
USB cable, or USB hub.
1002
 
						

							Cannot Communicate with the Machine with USB Connection
Check1 Make sure that the machine is turned on.
Check2 Make sure that the USB cable is connected properly.
See 
Connecting the Machine to the Computer Using a USB Cable  to connect the USB cable properly.
Check3
 Do not start up IJ Network Tool while printing.
Check4 Do not print while IJ Network Tool is running.
Check5 Make sure that  Enable bidirectional support  is selected in the Ports sheet of
the properties dialog box of the printer driver.
How to Open the Printer Driver Setup Window
1003
 
						

							The Display on the Touch Screen Cannot Be Seen At All
•
If the POWER lamp is off:
The machine is not powered on. Connect the power cord and press the  ON button.
•
If the POWER lamp is lit:
The touch screen may be in the screen-saver mode. Tap the touch screen.
1004
 
						

							An Unintended Language Is Displayed on the Touch Screen
Select the language you want to be displayed according to the following procedure.
1.
Press the HOME button and wait for about 5 seconds.
2.
Flick the HOME screen, then tap  Setup .
Using the Operation Panel
3.
Tap  Device settings .
4.
Tap the fifth setting item from the top.
5.
Tap the language for the touch screen.
1005
 
						

							Print Head Holder Does Not Move to the Position for Replacing
Important
•
The print head holder moves to the position for replacing only when an ink tank runs out of ink. If no ink
tanks run out of ink, the print head holder does not move even though you open the front cover.
Check1  Is the POWER  lamp off?
Check if the  POWER lamp is lit.
The print head holder will not move unless the power is on. If the  POWER lamp is off, close the front cover and
turn the machine on.
While the  POWER lamp is flashing, the machine is initializing. Wait until the  POWER lamp stops flashing and
remains lit, and then open the front cover again.
Check2  Is an error message displayed on the touch screen?
Close the front cover, follow the Support Code (error number) displayed in the error message to resolve the
error, and then reopen it. For details on how to resolve the error, refer to 
Support Code List .
Check3
 Has the front cover been left open for 60 minutes or longer?
If the front cover is left open for more than 60 minutes, the print head holder moves to the position to protect it to
prevent the print head from drying out. Close and reopen the front cover to return the print head holder to the
position for replacing.
1006
 
						

							Printer Status Monitor Is Not Displayed
Check Is the printer status monitor enabled?
Make sure that  Enable Status Monitor  is selected on the Option menu of the printer status monitor.
1.
Open the printer driver setup window.
How to Open the Printer Driver Setup Window
2.
On the  Maintenance  sheet, click View Printer Status .
3.
Select Enable Status Monitor  on the Option menu if it is not selected.
1007
 
						

							Problems with Installation/Downloading
Cannot Install the MP Drivers
Easy-WebPrint EX Does Not Start Up or Easy-WebPrint EX Menu Does Not
Appear
How to Update MP Drivers in Network Environment
Uninstalling IJ Network Tool
1008
 
						

							Cannot Install the MP Drivers
•
If the installation does not start even after the Setup CD-ROM is inserted into your computer'sdisc drive:
Start the installation following the procedure below.
1.
Select items as shown below.
◦
In Windows 8.1 or Windows 8, select the  Explorer icon in Taskbar  on Desktop , then select
Computer  from the list on the left.
◦
In Windows 7 or Windows Vista, click  Start then  Computer .
◦
In Windows Vista, click  Start then  Computer .
◦
In Windows XP, click  Start then  My Computer .
2.
Double-click the  CD-ROM  icon on the displayed window.
If the contents of the CD-ROM are displayed, double-click  MSETUP4.EXE.
If you cannot install the MP Drivers with the Setup CD-ROM, install them from our website.
Note
•
If the CD-ROM icon is not displayed, try the following:
•
Remove the CD-ROM from your computer, then insert it again.
•
Restart your computer.
If the icon is not yet displayed, try different discs and see if they are displayed. If other discs are displayed, there is a problem with the Setup CD-ROM. In this case, contact the service center.
1009
 
						

							•If you are unable to proceed beyond the Printer Connection screen:
Note
•
The printer is not detected. Check the connection. may be displayed depending on the
computer you use.
Check1  Make sure that the USB cable is securely plugged in to the machine and the
computer.
Check2  Follow the procedure below to connect the machine and the computer
again.
1.
Turn the machine off.
2.
Unplug the USB cable from the machine and the computer, then connect it again.
3.
Turn the machine on.
Check3  If you cannot resolve the problem, follow the procedure below to reinstall the
MP Drivers.
1.
Click  Cancel .
2.
Click Start Over  on the Installation Failure  screen.
3.
Click Exit on the "MAXIFY XXX" screen (where "XXX" is your machine's name), then remove the CD-
ROM.
4.
Turn the machine off.
5.
Restart the computer.
6.
Make sure that you have no application software running.
7.
Insert the CD-ROM again, then install the MP Drivers.
1010