Canon Maxify Mb5020 User Guide

							4.
After wiping, close the document feeder cover by pushing it until it clicks into place.
5.
Close the document tray.
231
 
						

							Cleaning the Paper Feed RollerIf the paper feed roller is dirty or paper powder is attached to it, paper may not be fed properly.
In this case, clean the paper feed roller. Cleaning will wear out the paper feed roller, so perform this only
when necessary.
You need to prepare: three sheets of A4 or Letter-sized plain paper1.
Make sure that the power is turned on.
2.
Flick the HOME screen, then tap   Setup .
Using the Operation Panel
The setup menu screen will appear.
3.
Tap   Maintenance .
The  Maintenance  screen will appear.
4.
Tap Roller cleaning .
The confirmation screen will appear.
5.
Tap Yes.
6.
Follow the message to remove any paper from the cassette.
7.
Tap  OK.
The paper feed roller will rotate as it is cleaned.
8.
Make sure that the paper feed roller has stopped rotating, then follow the message to load
three sheets of A4 or Letter-sized plain paper in the cassette.
9.
Extend the output tray extension, then open the paper output support.
10.
Tap  OK.
232
 
						

							The machine starts cleaning. The cleaning will be complete when the paper is ejected.11.
When the completion message appears, tap OK.
If the problem is not resolved after cleaning the paper feed roller, contact the service center.
233
 
						

							Cleaning the Inside of the Machine (Bottom Plate Cleaning)Remove stains from the inside of the machine. If the inside of the machine becomes dirty, printed paper mayget dirty, so we recommend performing cleaning regularly.
You need to prepare: a sheet of A4 or Letter-sized plain paper* * Be sure to use a new piece of paper.1.
Make sure that the power is turned on.
2.
Flick the HOME screen, then tap   Setup .
Using the Operation Panel
The setup menu screen will appear.
3.
Tap   Maintenance .
The  Maintenance  screen will appear.
4.
Tap Bottom plate cleaning .
The confirmation screen will appear.
5.
Tap Yes.
6.
Follow the message to remove any paper from the cassette, then tap  OK.
7.
Fold a single sheet of A4 or Letter-sized plain paper in half widthwise, then unfold the
paper.
8.
Fold one side of the opened paper in another half, aligning the edge with the center crease,
unfold the paper, then tap  OK.
234
 
						

							9.
Load only this sheet of paper in the cassette with the ridges of the creases facing up and
the edge of the half with no crease facing to the far side.
10.
Extend the output tray extension, then open the paper output support.
11.
Tap  OK.
The paper cleans the inside of the machine as it feeds through the machine. Check the folded parts of the ejected paper. If they are smudged with ink, perform Bottom Plate Cleaning
again.
12.
When the completion message appears, tap  OK.
Note
•
When performing Bottom Plate Cleaning again, be sure to use a new piece of paper.
If the problem is not resolved after performing cleaning again, the protrusions inside the machine may be
stained. Wipe off any ink from the protrusions using a cotton swab or the like.
Important
•
Be sure to turn off the power and unplug the power cord before cleaning the machine.
•
The power cannot be turned off while the machine is sending or receiving a fax, or when unsent faxes are stored in the machine's memory. Make sure if the machine completed sending or
receiving all the faxes before unplugging the power cord.
•
The machine cannot send or receive faxes when the power is turned off.
•
If the power cord is unplugged, all documents stored in the machine's memory will be lost. Send or
print a necessary document, or save it on a USB flash drive before unplugging the power cord.
235
 
						

							236
 
						

							Cleaning the Pad in the CassetteIf the pad in a cassette is smeared with paper powder or dirt, two or more sheets of paper may be ejected.
Follow the procedure below to clean the pad in a cassette.
You need to prepare: cotton swab1.
Pull out the cassette from the machine, then remove all the paper.
2.
Clean the pad (A) sideways with a moistened cotton swab.
Important
•
After cleaning the smeared pad, dry it completely.
3.
Reload the paper, then insert the cassette into the machine.
Note
•
If a message is displayed on the screen after inserting the cassette into the machine, tap Register .
If the problem is not resolved, contact the service center.
237
 
						

							Changing the Machine Settings
Changing Machine Settings from Your Computer
Changing the Machine Settings Using the Operation Panel
Registering the Favorite Settings (Custom profiles)
Checking the Total Number of Uses of the Machine
238
 
						

							Changing Machine Settings from Your Computer
Changing the Print Options
Registering a Frequently Used Printing Profile
Managing the Printer Power
Reducing the Printer Noise
Changing the Printer Operation Mode
239
 
						

							Changing the Print OptionsYou can change the detailed printer driver settings for print data that is sent from an application software.
Specify this option if you encounter print failures such as part of an image data being cut off.
The procedure for changing the print options is as follows:1.
Open the printer driver setup window
2.
Click  Print Options...  on the Page Setup  tab
The Print Options  dialog box opens.
Note
•
When you use the XPS printer driver, the functions available to you are different.
3.
Change the individual settings
If necessary, change the setting of each item, and then click  OK.
The  Page Setup  tab is displayed again.
240