Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Administrators Guide

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
957 Terminal Parameters 
17
Display Mode
Determines how the #) and ~ characters appear on the 603 phone’s display.This 
field only appears if Customize Parameters is 
y.
DLI Voltage Level
Determines whether DCP Line Voltage used by the telephones is forced high, 
forced low, or allowed to automatically adjust. This field only appears if 
Customize Parameters is 
y.
Handset Expander Enabled
Determines whether the telephone will reduce noise on the handset. This field 
appears only if Customize Parameters is 
y.
Primary levels
The following fields only appear if Customize Parameters is set to 
y. In each case, 
if the field is blank, the system uses the default setting from the Default Parameter 
Set. Also, these fields all require the same input; valid entries are from 
-44.0 db 
through 
+14.0 db in 0.5 increments (for example, -44.0, -43.5, -43.0 and son on).
Vo l u m e
Voice Transmit (dB) 
Determines the volume of voice outbound from the telephone.
Voice Receive (dB) 
Determines the volume of voice inbound to the telephone.
Valid entries Usage
1
If this field is set to 1, the # and ~ do not change.
2If this field is set to 2, the 603 phone displays a # as a British 
pound sterling symbol and a ~ as a straight overbar.
Valid entries Usage
y
If the field is y, the telephone reduces background noise. 
Valid entries Usage 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
958 Terminal Parameters 
17
Voice Sidetone (dB) 
Determines the volume of voice fed back from the handset voice microphone to 
the user’s ear.
Touch Tone Sidetone (dB) 
Determines the touchtone volume fed back from the telephone when a users 
presses a button.
Touch Tone Transmit (dB) —
Determines the touchtone volume fed outbound from the telephone.
NOTE:
You cannot administer all five of the Primary Level fields to +14.0 dB. If 
you attempt to submit the Terminal Parameters screen with all Primary 
Levels set to +14.0 dB, you receive an error message.
Adjunct levels
The following fields appear only if you are administering 8400-series telephones 
and if Customize Parameters is 
y. In each case, if the field is blank, the system 
uses the default setting from the Default Parameter Set. Also, these fields all 
require the same input; valid input is listed in “Primary levels” above.
Voice Transmit (dB) 
Determines the volume of voice outbound from the adjunct.
Voice Receive (dB) 
Determines the volume of voice inbound to the adjunct.
Voice Sidetone (dB) 
Determines the volume of voice fed back from the handset voice microphone to 
the user’s ear.
Touch Tone Sidetone (dB) 
Determines the touchtone volume fed back from the telephone when a users 
presses a button. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
959 Terminating Extension Group 
17
Terminating Extension Group
This screen defines a Terminating Extension Group (TEG). Any phone can be 
assigned as a TEG member; however, only a multi-appearance phone can be 
assigned a TEG button with associated status lamp. The TEG button allows the 
phone user to select a TEG call appearance for answering or for bridging onto an 
existing call.
The TEG members are assigned on an extension number basis. Call reception 
restrictions applicable to the group are specified by the group class of restriction 
(COR). The group COR takes precedence over an individual member’s COR. The 
members could all be termination restricted but still receive calls if the group is 
not restricted.
The system allows for as many as 32 TEGs with up to 4 members each. An 
extension number can be assigned to more than one TEG but can have only one 
appearance of each group.
Field descriptions for page 1
Screen 206. Terminating Extension Group 
Group Number
A display-only field when the screen is accessed using an administration 
command such as 
add or change.
change term-ext-group 1  Page   1 of   1
                       TERMINATING EXTENSION GROUP
    Group Number: 1  Group Extension:
      Group Name:  Coverage Path:
   Security Code:  COR: 1
TN: 1
ISDN Caller Disp:                                 LWC Reception: none
      AUDIX Name:  Messaging Server Name:
GROUP MEMBER ASSIGNMENTS
    Ext     Name                            Ext     Name
 1: 51001   27 character name sta 51001  3:
 2:                                      4: 51002   27 character name sta 51002 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
960 Terminating Extension Group 
17
Group Extension
Enter the extension of the terminating extension group.
Group Name
Enter the name used to identify the terminating extension group.
Coverage Path
Enter a number for the call coverage path for this group. A TEG cannot serve as a 
coverage point; however, calls to a TEG can redirect to coverage.
Security Code
COR
TNValid entries Usage
1 to 5 digits Unused extension number (may not be a VDN extension)
blank Do not leave blank
Valid entries Usage
1
 to 999
t1
 to t999time of day table
Valid entries Usage
4-digit security code This code is used for the Demand Print feature.
Valid entries Usage
0
 through 95Enter the class of restriction (COR) number that reflects the 
desired restrictions.
Valid entries Usage
1
 to 20Enter the Tenant Partition number. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
961 Terminating Extension Group 
17
ISDN Caller Disp
This field is required if, on the System-Parameters Customer-Options screen, the 
ISDN-PRI or ISDN-BRI Trunks field is 
y.
LWC Reception
Defines the source for Leave Word Calling (LWC) messages.
AUDIX Name
Name of the AUDIX machine as it appears in the Node Names screen. Only 
appears for an G3r configuration.
Valid entries Usage
grp-name
Specify whether the TEG group name or member name 
(member of TEG where call terminated) will be sent to the 
originating user.
mbr-nameSpecify whether the TEG group name or member name 
(member of TEG where call terminated) will be sent to the 
originating user.
blank If the ISDN-PRI or ISDN-BRI Trunks field is 
n, leave blank.
Valid entries Usage
audix
For G3i systems, if LWC is attempted, the messages are 
stored in AUDIX.
msa-speFor G3i systems, if LWC is attempted, the messages are 
stored in the system processing element (spe).
none For G3i systems, if LWC is attempted, the messages are not 
stored.
audixFor G3r systems, if LWC is attempted, the messages are 
stored in AUDIX.
msaFor G3r systems, if LWC is attempted, the messages are 
stored in the Message Server Adjunct - Switch Processor.
speFor G3r systems, if LWC is attempted, the messages are 
stored in the system processing element (spe).
none For G3r systems, if LWC is attempted, the messages are not 
stored.
Valid entries Usage
Unique identifiers for adjunct equipment. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
962 Time of Day Coverage Table 
17
Messaging Server Name
Name of the server as it appears in the Node Names screen. Only appears for G3r 
configurations.
Group Member Assignments — Ext
Enter the extension number (may not be a VDN extension) assigned to a station.
Group Member Assignments — Name
This display-only field shows the name assigned to the preceding extension 
number when the TEG member’s phone is administered.
Time of Day Coverage Table 
This screen allows up to five different coverage paths, associated with five 
different time ranges, for each day of the week. Only one coverage path can be in 
effect at any one time.
Field descriptions for page 1
Screen 207. Time of Day Coverage Table Valid entries Usage
Unique identifiers for messaging server equipment.
Valid entries Usage
An extension number
change coverage time-of-day 3
TIME OF DAY COVERAGE TABLE 3___
Act CVG Act CVG Act CVG Act CVG Act CVG
Time PATH  Time PATH  Time PATH  Time PATH Time PATH
Sun 00:00 ____  __:__ ____   __:__ ____  __:__ ____  __:__ ____
Mon 00:00 ____  __:__ ____   __:__ ____  __:__ ____  __:__ ____
Tue 00:00 ____  __:__ ____   __:__ ____  __:__ ____  __:__ ____
Wed 00:00 ____  __:__ ____   __:__ ____  __:__ ____  __:__ ____
Thu 00:00 ____  __:__ ____   __:__ ____  __:__ ____  __:__ ____
Fri 00:00 ____  __:__ ____   __:__ ____  __:__ ____  __:__ ____
Sat 00:00 ____  __:__ ____   __:__ ____  __:__ ____  __:__ ____ 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
963 Time of Day Routing Plan 
17
Time of Day Coverage Table
A display-only field when the screen is accessed using an administration 
command. Specifies the Time of Day Coverage Table number. Up to 999 can be 
administered.
Act Time
Specify the activation time of the coverage path administered in the next CVG 
PATH field. Enter the information in 24-hour time format.
CVG Path
Enter the coverage path number.
Time of Day Routing Plan 
Use this screen to set up Time of Day Routing Plans. You can route AAR and 
ARS calls based on the time of day each call is made. You can design up to 8 Time 
of Day Routing Plans, each scheduled to change up to 6 times a day for each day 
in the week.
Match the Time of Day Routing Plan PGN# with the PGN# field on the Partition 
Routing Table for the route pattern you want to use.
NOTE:
Automatic Route Selection (ARS) or Private Networking, AAR/ARS 
Partitioning, and Time of Day Routing must be enabled on the 
Valid entries Usage
00:01
 to 23:59If there are time gaps in the table, there will be no coverage 
path in effect during those periods. The first activation time for 
a day is set to 00:00 and cannot be changed. Activation times 
for a day must be in ascending order from left to right.
Valid entries Usage
1
 through 9999For the G3r configurations
1 through 999For the G3si configurations 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
964 Toll Analysis 
17
System-Parameters Customer-Options screen before you can use Time of 
Day Routing.
Screen 208. Time Of Day Routing Plan
Time of Day Routing Plan
Displays the Time of Day Routing Plan number (1 through 8).
Act Time
Specifies the time of day the route pattern (identified by PGN) begins.
PGN #
Identifies the route pattern for activation time listed.
Toll Analysis  
NOTE:
The Toll List field on this screen does not interact with or relate to the ARS Toll Table.
This screen associates dialed strings to the system’s Restricted Call List (RCL), 
Unrestricted Call List (UCL), and Toll List. You can force users to dial an account 
code if you associate dialed strings with CDR Forced Entry of Account Codes. 
Valid entries Usage
00:00
 to 23:59Time is represented using a 24 hour clock. List times for the 
same day in increasing order. There must be at least one entry 
for each day.
Valid entries Usage
1
 to 8Enter a PGN that matches the PGN and route pattern on the 
Partition Routing Table. There must be at least one entry for each 
day. 
change time-of-day 
TIME OF DAY ROUTING PLAN ___ Page 1 of 1
     Act    PGN   Act   PGN   Act    PGN   Act    PGN   Act    PGN   Act    PGN
     Time    #    Time   #    Time    #    Time    #    Time    #    Time    #
Sun  00:00   1   __:__   _    __:__   _    __:__   _    __:__   _    __:__   _
Mon  00:00   1   __:__   _    __:__   _    __:__   _    __:__   _    __:__   _
Tue  00:00   1   __:__   _    __:__   _    __:__   _    __:__   _    __:__   _
Wed  00:00   1   __:__   _    __:__   _    __:__   _    __:__   _    __:__   _
Thu  00:00   1   __:__   _    __:__   _    __:__   _    __:__   _    __:__   _
Fri  00:00   1   __:__   _    __:__   _    __:__   _    __:__   _    __:__   _
Sat  00:00   1   __:__   _    __:__   _    __:__   _    __:__   _    __:__   _ 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
965 Toll Analysis 
17
To maximize System security, it is recommended that toll calling areas be 
restricted as much as possible through the use of the RCL (Restricted Call List) 
and Toll List fields on this screen.
Screen 209. Toll Analysis 
Percent Full
Displays the percentage (0 to 100) of the system’s memory resources that have 
been used by AAR/ARS. If the figure is close to 100%, you can free-up memory 
resources.
Location
Display only field. Values other than “all” appear if the Multiple Locations field 
on the System Parameters Customer Options is 
y.
Dialed String
Valid display Usage
1
 to 44Defines the switch location for this Toll Analysis Table.
allIndicates that this Toll Analysis Table is the default for all port 
network (cabinet) locations. 
Valid entries Usage
digits 0 to 9
(up to 18 characters)Enter the dialed string you want the switch to 
analyze. 
*, x, Xwildcard characters
change toll analysis  Page 1 of 1
                                TOLL ANALYSIS                   Percent Full:_
Location:
                         Total        Toll  CDR  
    Dialed String      Min  Max  RCL  List  FEAC  1  2  3  4  5  6  7  8  9 10
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _
_____________________  ___  ___   _     _     _   _  _  _  _  _  _  _  _  _  _ 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
966 Toll Analysis 
17
Min
Max
RCL
Enter 
x to assign the Dialed String to the Restricted Call List (RCL). 
Toll List 
Valid entries Usage
1
 to Max Enter the minimum number of user-dialed digits the 
system collects to match to this dialed string.
Valid entries Usage
Min to 24Enter the maximum number of user-dialed digits the 
system collects to match to this dialed string.
Valid entries Usage
x
All entries of x and their associated dialed strings are referred 
to as the System’s Restricted Call List. The RCL can be 
assigned to any COR. A call attempt from a facility whose 
COR is marked as being associated with the RCL and whose 
dialed string matches a RCL dialed string field will be denied. 
The caller receives intercept treatment.
Valid entries Usage
x
Enter x to assign the Dialed String to the Toll List. 
Dialed String Min Max Toll List
0123x
1423x
20 10 10 x
21 10 10 x
30 10 10 x
31 10 10 x
40 10 10 x
41 10 10 x
50 10 10 x