Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Instructions Manual

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
647 Feature-Related System Parameters 
17
Self Station Display Enabled
Use this field to control the use of the 
INSPECT button for digital display phones.
Self Station Display allows a user to display the primary extension associated with 
a digital display phone. There are two methods: (1) enter a feature access code 
(FAC), and (2) use the 
INSPECT button. In either case, the display shows the 
primary extension associated with the phone where the FAC or 
NORMAL or EXIT 
button is entered. In the case of the FAC, the display continues until a 
display-altering event occurs (for instance, going on-hook or receiving an 
incoming call). In the case of the 
INSPECT button, the display continues until the 
user presses the 
NORMAL or EXIT button or until a display-altering event occurs.
Trunk-to-Trunk Transfer
Regulations in some countries control the settings for this field. See your Lucent 
Technologies representative for assistance.
Automatic Callback — No Answer Timeout 
Interval (rings)
Valid entries Usage
y
The primary extension does display when the INSPECT button is 
pressed.
n  The extension does not display when the INSPECT button is 
pressed.
Valid entries Usage
all
Enter all to enable all trunk-to-trunk transfers. This allows 
telephone users to set up trunk-to-trunk transfer, go on-hook 
without disconnecting the call, and forward the call to a remote 
location.
restrictedEnter restricted (restricted public) to restrict all public trunks 
(CO, WATS, FX, CPE, DID, and DIOD).
none Enter none to restrict all trunks (except CAS and DCS) from 
being transferred.
Valid entries Usage
2–9
.  Enter the number of times the callback call rings at the calling 
station before the callback call is canceled. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
648 Feature-Related System Parameters 
17
Call Park Timeout Interval (minutes)
Off-Premises Tone Detect Timeout Interval 
(seconds)
AAR/ARS Dial Tone Required
A second dial tone provides feedback to the user that additional dialing can occur.
Music/Tone on Hold
If you use equipment that rebroadcasts music or other copyrighted materials, you 
may be required to obtain a copyright license from, or pay fees to, a third party 
such as the American Society of Composers, Artists, and Producers (ASCAP) or 
Broadcast Music Incorporated (BMI). You can purchase a Magic OnHold
® 
system, which does not require such a license, from Lucent Technologies. This 
field does not appear if Tenant Partitioning is 
y on the System-Parameters 
Customer-Options screen. In that case, use the Te n a n t
 screen to establish Music 
on Hold. 
Valid entries Usage
1–90
.  Enter the number of minutes a call remains parked before it 
cancels.
Valid entries Usage
5–25
The number of seconds a call progress tone receiver (CPTR) 
tries to detect dial tone from a trunk during dialing. Once the 
time-out interval occurs, the call either outpulses on the trunk 
or gets intercept treatment depending on the setting of the 
Outpulse Without Tone field on page 6 of this screen.
Valid entries Usage
y/n
 Enter y to indicate a second dial tone is to be given to the 
calling party on a incoming tie or DID trunk call that is to be 
routed via AAR/ARS.
Valid entries Usage
music
tone
none
Indicates what a caller hears while on hold. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
649 Feature-Related System Parameters 
17
Port
Indicates the port number that provides Music-on-Hold access. This requires a 
port on a TN763 Auxiliary Trunk circuit pack or any supported Analog Line 
circuit pack. Appears when Music/Tone on Hold is 
music.
Music (or Silence) On Transferred Trunk Calls
Valid entries Usage
01
 through 22First and second characters are cabinet number
01 through 03
A
 through EThird character is carrier
01 through 20Fourth and fifth characters are slot number
01 through 04 
(Aux Trunk 
Port)Sixth and seventh characters are circuit number
01 through 16 
(Analog Port)
Valid entries Usage
all
Enter all to allow all transferred trunk calls to receive music 
until the call is answered if the Music-on-Hold feature is 
available.
no Enter no if trunk callers are to hear music (or silence if 
Music-on-Hold is not administered) while waiting to be 
transferred, and then ringback as soon as the transfer is 
completed till the call is answered.
call-waitEnter call-wait if trunk calls transferred to stations that require 
the call to wait hear music (if administered); all other 
transferred trunk calls receive ringback tone. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
650 Feature-Related System Parameters 
17
DID/Tie/ISDN Intercept Treatment
Messaging Service Adjunct (MSA) Connected
Internal Auto-Answer of 
Attd-Extended/Transferred Calls
This only applies to digital telephones (except BRI) with a headset or 
speakerphone capability.
Valid entries Usage
A recorded 
announcement 
extension Toll charges do not apply to DID and private network calls 
routed to an announcement.
attdFor system security, Lucent recommends entering attd in this 
field. This routes intercept calls to the attendant and, if the 
attendant receives several of these, they will know a problem 
exists.
Valid entries Usage
y
 Enter y if AUDIX Voice Power MSA is connected to the 
system. 
n 
Valid entries Usage
attd-extended
Enter attd-extended to enable IAA for only attendant extended 
calls.
bothEnter both to enable IAA for station transferred and attendant 
extended calls.
noneEnter none to disable IAA for all calls.
transferredEnter transferred to enable IAA for only station transferred 
calls. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
651 Feature-Related System Parameters 
17
Automatic Circuit Assurance (ACA) Enabled
If Automatic Circuit Assurance (ACA) Enabled is 
n, associated ACA fields will 
not display.
Must have an aca-halt button administered on the user’s station. If you enable 
this feature, complete the following ACA-related fields. 
ACA Referral Calls
Indicates where ACA referral calls generate. (Only appears when ACA Enabled 
is
y.)
ACA Referral Destination
The specified extension should be equipped with a display module. This field only 
appears if ACA Referral Calls is 
local or primary.
Valid entries Usage
y
 Enter y if ACA measurements will be taken.
n Otherwise, enter n.
Valid entries Usage
local
  Local referral calls generate on and for the local switch. 
primaryPrimary referral calls generate on the local switch for remote 
switches as well as the local switch. 
remoteRemote referral calls generate at another switch in a DCS 
network. In this case, the remote node number must also be 
entered. The remote node number is the same node number as 
defined on the Dial Plan screen. Also, ACA button status 
transmits to other switches when in a DCS network.
Valid entries Usage
An extension  Enter the extension on the local switch that is to receive the 
ACA referral call.
attdEnter attd for attendant. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
652 Feature-Related System Parameters 
17
ACA Short Holding Time Originating Extension 
and ACA Long Holding Time Originating 
Extension
ACA Remote PBX Identification
This field only appears if ACA Referral Calls is 
remote. 
Abbreviated Dial Programming by Assigned 
Lists
Auto Abbreviated/Delayed Transition Interval 
(rings)
Valid entries Usage
An unassigned 
extension Do not use the same extension number for both fields. The 
specified extensions are assigned automatically by the system 
when the screen is submitted. These fields only display if 
ACA Referral Calls is 
local or primary.
Valid entries Usage
1
–63Enter a number to identify the switch in a DCS network that 
makes the referral call. Do not define the remote switch 
identified in this field as 
local on the system’s Dial Plan 
screen.
Valid entries Usage
y
   Enter y to allow programming by station’s assigned list.
nEnter n  if using Program Access code to indicate which 
personal list is to be programmed.
Valid entries Usage
1
–16 Enter the number of rings before an automatic abbreviated/ 
delayed transition is triggered for a call 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
653 Feature-Related System Parameters 
17
Protocol for Caller ID Analog Terminals
Determines the protocol/tones sent to a Caller ID phone.
Field descriptions for page 2
Screen 86. Feature-Related System Parameters screen
Maximum Number of Messages Per Station 
(when MSA not in service)
Valid entries Usage
Bellcore
Enter Bellcore for Bellcore protocol with 212 modem protocol 
tones. Used in the U.S. and similar countries.
V23-Bell Enter V23-Bell for Bellcore protocol with V.23 modem tones. 
Used in Bahrain and similar countries.
Valid entries Usage
0–125
  The maximum number of LWC Messages that can be stored by 
the system for a telephone at a given time.
change system-parameters features   Page 2 of 9
                       FEATURE-RELATED SYSTEM PARAMETERS
LEAVE WORD CALLING PARAMETERS
  Maximum Number of Messages Per Station (when MSA not in service): 10_
Maximum Number of External Calls Logged Per Station: 0
Message Waiting Indication for External Calls? n
  Stations with System-wide Retrieval Permission (enter extension)
    1: 34430    3: attd_    5: _____    7: _____    9: _____
    2: 34412    4: _____    6: _____    8: _____   10: _____
WARNING!   SEE USER DOCUMENTATION BEFORE CHANGING TTI STATE
Terminal Translation Initialization (TTI) Enabled? y
TTI State: voice   TTI Security Code: _______
Record PSA/TTI Transactions in History Log? _
COR for PSA Dissociated Sets: _
CPN, ANI for PSA Dissociated Sets: _
Prohibit Bridging Onto Calls with Data Privacy? _
Enhanced Abbreviated Dial Length (3 or 4)? _
Default Multimedia Outgoing Trunk Parameter Selection: 2x64
WIRELESS PARAMETERS
Radio Controllers with Download Server Permission (enter board location)
1: ___ 2: ___ 3: ___ 4: ___ 5: ___ 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
654 Feature-Related System Parameters 
17
Maximum Number of External Calls Logged Per 
Station
When an external call is not answered, the switch keeps a record of up to 15 calls 
(provided information on the caller identification is available) and the phone’s 
message lamp lights. The phone set displays the names and numbers of 
unsuccessful callers.
Message Waiting Indication for External Calls
Provides a message waiting indication when external calls are logged.
Stations With System-wide Retrieval 
Permission (enter extension)
Valid entries Usage
0 
- 15The maximum number of calls that can be logged for each user. 
The assigned number cannot be larger than the entry in the 
Maximum Number of Messages Per Station (when MSA not in 
service) field.
Valid entries Usage
y
The message waiting indication for a particular station is on 
whenever an external call is logged.
nThe log of external calls has no impact on the message waiting 
indication.
Valid entries Usage
An assigned station extension. Enter up to 10 telephone extension numbers 
that can retrieve LWC Messages for all other 
telephones. A VDN extension is not allowed 
attdAn entry of attd gives retrieval permission to 
all attendants. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
655 Feature-Related System Parameters 
17
Terminal Translation Initialization (TTI) Enabled
Terminal Translation Initialization (TTI) must be enabled on the 
System-Parameters Customer-Options screen before the TTI fields can be 
administered.
!CAUTION:
Changing the TTI Enable field from 
n to y or from y to n triggers a 
background maintenance task that either generates (when changed to 
y) or 
removes (when changed to 
n) TTI port translation for unadministered ports 
in the system.
TTI State
The value of this field determines what type of TTI default port translation is 
generated for unadministered digital ports. This field appears when Terminal 
Translation Initialization (TTI) Enabled is 
y.
TTI Security Code
(This is also known as the TTI authorization code but is not the same as system 
authorization codes.) This field appears when Terminal Translation Initialization 
(TTI) Enabled is 
y.
Valid entries Usage
y
Enter y to start a background maintenance task to generate 
TTI port translations for unadministered ports on 
TTI-supported circuit packs.
n Enter n to remove existing TTI port translations and make 
sure no new TTI port translations will be generated.
Valid entries Usage
data
resume
Allows the TTI state to return to what it was before TTI was 
manually suspended.
suspendAllows any current generation or removal of TTI port 
translations to be halted and access to TTI will also be denied.
voice Enter voice for the Personal Station Access feature.
Valid entries Usage
1- to 7-digit code This is the code that TTI users must enter when 
accessing TTI from their telephones 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
656 Feature-Related System Parameters 
17
Record PSA/TTI Transactions in History Log
COR for PSA Dissociated Sets
CPN, ANI for PSA Dissociated Sets
Appears when the COR for PSA Dissociated Sets field is non-blank. Specifies the 
ISDN calling party number (CPN), R2-MFC ANI, and CAMA CESID applied to 
calls made from PSA dissociated sets, if no system-wide calling party information 
has been administered for those protocols on their respective administration 
screens.
Prohibit Bridging Onto Calls with Data Privacy
Enhanced Abbreviated Dial Length (3 or 4)
The administrator may not be able to use all entry slots because of system capacity 
constraints.
Valid entries Usage
y/n
 If y, TTI and PSA transactions record in the history log. You 
access these transactions via the List History command. 
Valid entries Usage
1-95
  Enter the class of restriction to apply to calls made from 
dissociated telephones. See ‘‘
Personal Station Access’’ on 
page 1470 for more information. 
Valid entries Usage
1-20 digits Enter the calling party number or automatic number 
identification for calls made from dissociated telephones.
Valid entries Usage
y/n
 Enter y to protect calls from bridge-on by any party, including 
Service Observing, Intrusion, Verify, and Bridging.
Valid entries Usage
3
A value of 3 makes 1000 Enhanced List entries available to the 
administrator
4A value of 4 makes 10,000 entries available.