Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Instructions Manual

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
897 Station 
17
Adjunct Supervision
Adjunct Supervision appears when the Type field is 
500, 2500, k2500, 8110, ops, 
ds1fd, ds1sa, VRU, VRUFD, or VRUSA.
Assigned Member — Ext
The system automatically assigns this extension. This is the extension of the user 
who has an associated Data Extension button and shares the module.
Assigned Member — Name
Display-only field that shows the name associated with the extension shown in the 
Assigned Member - Ext field.
Att. Call Waiting Indication
Attendant call waiting allows attendant-originated or attendant-extended calls to a 
busy single-line phone to wait and sends distinctive call-waiting tone to the 
single-line user. 
Valid entries Usage
y
 Enter y if an analog disconnect signal is sent automatically to 
the port after a call terminates. Analog devices (such as 
answering machines and speakerphones) use this signal to turn 
the devices off after a call terminates. 
nSet this field to n so hunt group agents are alerted to incoming 
calls. In a hunt group environment, the disconnect signal 
blocks the reception of zip tone and incoming call notification 
by an auto-answer station when a call is queued for the station. 
Valid entries Usage
y/n 
Enter y to assign Attendant Call Waiting to the phone. 
You should not set this field to y, if the Data Restriction field is 
y or the Switchhook Flash field is n, or if Data Privacy is 
enabled for the phone’s class of service (COS). If any of these 
conditions are true, the phone cannot accept or handle call 
waiting calls. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
898 Station 
17
Audible Message Waiting
The Audible Message Waiting tone indicates that the user has a waiting message. 
This field appears only if Audible Message Waiting is set to 
y on the 
System-Parameters Customer-Options screen. 
Note that this field does not control the Message Waiting lamp.
Audix Name
Specifies which AUDIX is associated with the station.
Auto Answer
In EAS environments, the auto answer setting on the Agent LoginID screen may 
override a station’s setting when an agent logs in there.
NOTE:
For analog stations, if Auto Answer is acd and the station is off-hook and 
idle, only the ACD split/skill calls and direct agent calls auto answer; 
non-ACD calls receive busy treatment. If the station is active on an ACD 
call and a non-ACD call arrives, the Agent receives call-waiting tone.
Valid entries Usage
y/n
Enter y if you want the phone user to receive stutter dial tone 
when they have a waiting message and they go off-hook. 
Valid entries Usage
Names assigned 
to an AUDIX 
adjunctMust contain a user-defined adjunct name that was previously 
administered in the Node-Names screen. 
Valid entries Usage
all
Enter all to allow all calls (ACD and non-ACD) terminated to 
an idle station to be cut through immediately.
acdEnter acd to allow only ACD split /skill calls and direct agent 
calls to auto answer. If this field is 
acd, Non-ACD calls 
terminated to a station ring audibly.
none Enter none to cause all calls terminated to this station to 
receive an audible ringing treatment. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
899 Station 
17
Auto Select Any Idle Appearance
BCC
Appears when ISDN-PRI or ISDN-BRI Trunks is enabled on the 
System-Parameters Customer-Options screen. Display-only field set to 0 for 
stations (that is, indicates voice or voice-grade data). 
Refer to ‘‘
Generalized route selection’’ on page 1351 for a detailed description of 
Bearer Capability Classes (BCC) and their ability to provide specialized routing 
for various types of voice and data calls. The BCC value is used to determine 
compatibility when non-ISDN facilities are connected to ISDN facilities (ISDN 
Interworking).
Bridged Call Alerting
If Bridged Call Alerting is n and Per Button Ring Control is n, audible ringing is 
suppressed for incoming calls on bridged appearances of another phone’s primary 
extension.
Building
Enter a valid building location. See ‘‘
Site Data’’ on page 894 for valid entries.
Button Assignments
Enter the abbreviated software name to assign a feature button. For a list of 
feature buttons, refer to ‘‘
Telephone feature buttons’’ on page 71.
NOTE:
If you want to use Terminal Translation Initialization (TTI), you must assign 
a call appearance (call-appr) to the first button position. TTI needs the 
button on the first call appearance to get dial tone.
Valid entries Usage
y/n
Enter y to allow automatic selection of any idle appearance for 
transferred or conferenced calls. The system first attempts to 
find an idle appearance of the call being transferred or 
conferenced. If that attempt fails, the system selects the first 
idle appearance. 
Valid entries Usage
y/n
Enter y to enable audible ringing for TEG, PCOL, bridged 
appearances, or Data Extension calls. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
900 Station 
17
Cable
You can use this field to identify the cable that connects the phone jack to the 
system. You also can enter this information in the Blank column on the Port 
Assignment Record.
Caller ID Message Waiting Indication
Appears when the Type field is CallrID. For CallrID type phones or analog phones 
with Caller ID adjuncts only.
NOTE:
The Caller ID Message Waiting Indication administration is independent of 
the administration of LED or NEON lamp DEFINITY ECS Message 
Waiting Indication (MWI). For example, it is possible to administer a Caller 
ID phone with the Caller ID Message Waiting Indication field set to 
n and 
the Message Waiting Indicator field set to 
neon.
Call Waiting Indication
This allows user, attendant-originated, and outside calls to busy single-line phone 
to wait and sends a distinctive call-waiting tone to the single-line user. This 
feature is denied if Data Restriction is 
y or Switchhook Flash is n, or if Data 
Privacy is active via the phone COS assignment.
CDR Privacy
This option allows digits in the called number field of an outgoing call record to 
be blanked, on a per-station basis. You administer the number of blocked digits 
system-wide in the Privacy - Digits to Hide field on the CDR System Parameters 
screen. 
COR
Enter a Class of Restriction (COR) number to select the desired restriction.
Valid entries Usage
y/n
Enter y to allow aliasing of various non-Lucent phones and 
adjuncts.
Valid entries Usage
y/n
Enter y to activate Call Waiting Termination for the phone.
Valid entries Usage
y/n
Enter y to enable Call Privacy for each station. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
901 Station 
17
Cord Length
Enter a number to specify the length (in feet) of the cord attached to the receiver.
COS
Enter the desired Class of Service (COS) number to select allowed features.
Country Protocol
Enter the protocol that corresponds to your supported initialization and codesets. 
The Country Protocol must match any previously-administered endpoint on the 
same port.
Coverage After Forwarding
This field governs whether an unanswered forwarded call is provided coverage 
treatment. 
Coverage Msg Retrieval
Applies if the phone is enabled for LWC Reception.
Valid entries Usage
1
  United States (Bellcore National ISDN)
2Australia
etsiETSI (Europe)
3Japan
6Singapore
Valid entries Usage
y
Coverage treatment is provided after forwarding regardless of 
the value of the Coverage After Forwarding field on the 
System Parameters - Call Coverage/Call Forwarding screen.
nNo coverage treatment is provided after forwarding regardless 
of the value of the Coverage After Forwarding field on the 
System Parameters - Call Coverage/Call Forwarding screen.
s(ystem)
Indicates that call processing uses the Coverage After 
Forwarding field on the ‘‘
System Parameters Call Coverage / 
Call Forwarding’’ screen. To override the system-wide 
parameter for a given station, set this field to 
y or n.
Valid entries Usage
y/n
Enter y to allow users in the phone’s Coverage Path to retrieve 
Leave Word Calling (LWC) messages for this phone. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
902 Station 
17
Coverage Module
Coverage Path 1 or Coverage Path 2
Enter a coverage-path number or time-of-day table number from a 
previously-administered Call Coverage Path screen or Time of Day Coverage 
Table screen.
NOTE:
If Modified Misoperation is active (Misoperation Alerting is y on the 
Feature-Related System Parameters screen), you must assign a Coverage 
Path to all stations on the switch.
CRV Length
Only for ASAI stations. Enter 
1 or 2 to indicate the length of CRV for each 
interface. 
Data Extension
Enter the extension assigned to the data module.
Data Module
Data Restriction
Data restriction provides permanent protection and cannot be changed by the 
phone user. Do not assign a Data Restriction if Auto Answer is 
all or acd.
Valid entries Usage
y
Enter y to indicate that a coverage module is connected to the 
station. Once you enter y, the system displays an additional 
page that allows you to assign the buttons for the module.
Valid entries Usage
y/n
Enter y to indicate that you want to administer a data module 
with this phone. Entering 
y displays the Data Module screen.
Valid entries Usage
y/n
Enter y to prevent tones, such as call-waiting tones, from 
interrupting data calls. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
903 Station 
17
Default Dialing Abbreviated Dialing Dial Code
Appears only when the Special Dialing Option is set to default. Enter a list 
number associated with the abbreviated dialing list. 
When the user goes off-hook for a data call and presses 
RETURN following the 
DIAL prompt, the system dials the AD number. The data call originator also can 
perform data-terminal dialing by specifying a dial string that may or may not 
contain alphanumeric names.
Display Caller ID
Appears when the Type field is CallrID. For CallrID type phones or analog phones 
with Caller ID adjuncts only.
Display Cartridge
For 7404 D phones only. Enter 
y to indicate there is a display cartridge associated 
with the station. This displays an additional page to allow you to assign display 
buttons for the display cartridge.
Display Client Redirection
Only administrable if Hospitality is enabled on the System-Parameters 
Customer-Options screen. This field affects the phone display on calls that 
originated from a station with Client Room Class of Service.
NOTE:
For stations with an audix station type, AUDIX Voice Power ports, or ports 
for any other type of messaging that needs display information, Display 
Client Redirection must be set to y.
Valid entries Usage
y/n
Enter y to allow transmission of calling party information to 
the Caller ID phone or adjunct.
Valid entries Usage
y
  When set to y, the redirection information for a call originating 
from a Client Room and terminating to this station displays.
n  When set to n, this station’s display does not show the 
redirection information for all calls originating from a Client 
Room (even redirected calls) that terminate to this station. Only 
the client name and extension (or room, depending on what is 
administered on the ‘‘
Hospitality’’ screen) display. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
904 Station 
17
Display Language
Specifies the display language.
Distinctive Audible Alert
Endpt ID
Appears only if Endpt Init is 
y. Enter a unique 2-digit number (00–62) for this 
endpoint. Each Endpt ID field must have a unique value for each endpoint on the 
same port.
This field provides for multipoint configuration conformance to the Bellcore 
Terminal Initialization procedures. In these procedures, a multipoint configuration 
requires the last 2 digits of the Service Profile Identifier (SPID) be between 00 and 
63 and be binary unique for each endpoint. This field, combined with the SPID, 
gives the effective SPID administered into the terminal. Bellcore ISDN-1 requires 
the SPID programmed into the endpoint contain at least 9 digits. 
For example, if the SPID is 
1234, and Endpt ID is 01, then the SPID administered 
on the terminal is 000123401. The three leading zeros are necessary to create a 
9-digit SPID.
Valid entries Usage
english
  Enter the language you want users to see on their 
displays. 
french
italian
spanish
user-defined
Valid entries Usage
y/n
Enter y so the phone can receive the 3 different types of ringing 
patterns which identify the type of incoming calls.
Distinctive ringing may not work properly for off-premises 
telephones. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
905 Station 
17
Endpt Init 
Endpoint initialization is a procedure, required for multipoint operation, by which 
User Service Order Profile (USOP) is associated with an endpoint on the 
ISDN-BRI. This association is made via the SPID, administered into the system, 
and entered into the ISDN-BRI terminal. For an ISDN-BRI terminal to be 
operational in a multipoint configuration, both the administered SPID and the 
SPID programmed into the ISDN-BRI terminal must be the same. Therefore, the 
SPID of new or reused terminals must be programmed to match the administered 
SPID value. Appears only if MIM Support is 
y and indicates the terminal’s 
endpoint initialization capability.
Event Minimization
Allows you to minimize events sent on a link. This field appears only if you set 
Type to 
asai.
Expansion Module
Extension
Displays the extension for this station—this is either the extension you specified 
in the station command or the next available extension (if you used add station 
next).
Valid entries Usage
y
 Enter y if the terminal supports Bellcore ISDN-1 terminal 
initialization procedures. 
nEnter n for all other country protocols.
Valid entries Usage
y/n
Enter y when an application or library does not want to receive 
identical event reports over different associations.
When minimization is enabled, the switch sends a single event 
report on only one association and discards any remaining 
reports. It is up to the library or application to report this event 
to other interested parties or applications.
Valid entries Usage
y/n
Enter y if this phone has an expansion module. This will enable 
you to administer the buttons for the expansion module.  
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
906 Station 
17
Feature Module
Enter 
y to indicate the station is connected to a feature module. Entering y 
displays an additional page to allow you to assign feature buttons to the module.
Fixed TEI
This field appears only for ISDN-BRI data modules and ASAI links. It indicates 
that the endpoint has a fixed Terminal Endpoint Identifier (TEI).
The TEI identifies a unique access point within a service. You must administer 
TEIs for fixed TEI terminals. However, for terminals with the automatic TEI 
capability, the system dynamically assigns the TEI.
Floor
Enter a valid floor location. See ‘‘
Translation-ID Number Mismatch Interval 
(days)’’ on page 893 for valid entries.
H.320 Conversion
Allows H.320 compliant calls made to this phone to be converted to voice-only. 
Because the system can only handle a limited number of conversion calls, you 
may need to limit the number of telephones with H.320 conversion.
Headset
Enter 
y if the telephone has a headset.
HOT LINE DESTINATION — Abbreviated Dialing 
Dial Code
Appears only when Special Dialing Option is 
hot-line. 
Use Hot Line Service when very fast service is required and when you use a 
telephone only for accessing a certain facility. Hot Line Service allows single-line 
telephone users, by simply lifting the handset, to automatically place a call to a 
preassigned destination (extension, telephone number, or feature access code).
The Hot Line Service destination number is stored in an Abbreviated Dialing List. 
When the user goes off-hook on a Data Hot Line call, the system dials the AD 
number. 
Valid entries Usage
y/n
Entering y displays the TEI field.
For ASAI, enter 
y.