Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Instructions Manual

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
887 Security-Related System Parameters 
17
Number of Digits
This field tells the system how many digits to collect if the first and second digits 
match. Enter the length of the dialed number.
Security-Related System Parameters
You use this screen to determine when the switch reports a security violation. 
Many of the fields on this screen repeat for each type of security violation. We 
have explained them once here, but the usage is the same for all. Refer to 
‘‘
Security violations notification’’ on page 1491 for more information on security 
violations notification.
Field descriptions for page 1
Screen 181. Security-Related System Parameters Valid entries Usage
2
 For attd
2 through 5For aar, ars, and extension
2 through 4For tac (2 and 3 with DCS)
2 through 4For fac
change system-parameters security Page 1 of 2
SECURITY-RELATED SYSTEM PARAMETERS
SECURITY VIOLATION NOTIFICATION PARAMETERS
SVN Login Violation Notification Enabled? y
Originating Extension: _____ Referral Destination: _____
Login Threshold: 5_  Time Interval: 0:03
Announcement Extension: _____
SVN Remote Access Violation Notification Enabled? y
Originating Extension: _____ Referral Destination: _____
Barrier Code Threshold: 10  Time Interval: 0:03
Announcement Extension: _____
SVN Authorization Code Violation Notification Enabled? y
Originating Extension: _____ Referral Destination: _____
Authorization Code Threshold: 10  Time Interval: 0:03
Announcement Extension: _____ 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
888 Security-Related System Parameters 
17
SVN Login (Remote Access, AutoStation 
Security Code, Violation Notification Enabled
Originating Extension
The originating extension initiates the referral call in the event of a security 
violation. It also sends the appropriate alerting message or display to the referral 
destination.
Referral Destination
The referral destination receives the referral call when a security violation occurs. 
The referral destination telephone must have a display, unless the you assign an 
Announcement Extension. 
Valid entries Usage
y/n
Set to y if you want the switch to notify you when a login 
violation occurs. If this field is 
y, the next 5 fields appear so 
you can establish the parameters for what is considered a 
security violation.
Valid entries Usage
An unassigned 
extensionIf you establish notification for more than one type of security 
violations, you must assign a different extension to each one. 
When the switch generations a referral call, this extension and 
the type of violation appear on the display at the referral 
destination.
Valid entries Usage
An extension Enter the extension of the telephone, attendant console, or 
vector directory number (VDN) that you want to receive the 
referral call for each type of violation. This can be the same 
extension for all type of violations.
If you use a VDN, you must complete the Announcement 
Extension field. You can also use Call Vectoring Time-of-Day 
routing to route the referral call to different destinations based 
on the time of day or the day of the week.  
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
889 Security-Related System Parameters 
17
Login (Barrier Code, Authorization Code 
Security Code) Threshold
The value assigned to this field, in conjunction with Time Interval, determines 
whether a security violation has occurred. For example, if this field is 5, and time 
interval is 0:03, then five invalid access attempts within three minutes constitutes 
a security violation. 
Time Interval
The value of this field, in conjunction with Threshold, determines whether a 
security violation has occurred.
Announcement Extension
If you enter a value in this field, the switch calls the referral destination, then plays 
this announcement upon answer.
SVN Remote Access Violation Notification 
Enabled
Use these fields to establish parameters for remote access security violations. A 
remote access violation occurs if a user enters incorrect barrier codes. You cannot 
set the system to disable remote access following a security violation unless you 
have turned this on here. 
Valid entries Usage
1–99, 1–255
 for 
Station Security 
codeEnter the number of access attempts that are permitted before a 
referral call is made. In general, it is good to keep this number 
low. If you are doing testing and do not want to generate 
alarms, you might change this threshold temporarily.
Valid entries Usage
0:01
 to 7:59The range for the time interval is one minute to eight hours. 
Entered in the screen “x:xx.” For example, if you want the time 
interval to be one minute, you enter 0:01. If you want the time 
interval to be seven and one-half hours, you enter 7:30. 
Valid entries Usage
Valid extension The announcement extension where SVN 
violation announcement resides.  
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
890 Security-Related System Parameters 
17
SVN Authorization Code Violation Notification 
Enabled
Field descriptions for page 2
Screen 182. Security-Related System Parameters for G3r 
Screen 183. Security-Related System Parameters for G3si and G3csi 
change system-parameters security     Page 2 of 2
    SECURITY-RELATED SYSTEM PARAMETERS
SECURITY VIOLATION NOTIFICATION PARAMETERS
SVN Station Security Code Violation Notification Enabled? y
Originating Extension: _____  Referral Destination: _____
Station Security Code Threshold: 10 Time Interval: 0:03
Announcement Extension: _____
STATION SECURITY CODE VERIFICATION PARAMETERS
Minimum Station Security Code Length: 4
Security Code for Terminal Self Administration Required? y
ACCESS SECURITY GATEWAY PARAMETERS
SYSAM-LCL? n SYSAM-RMT? n
MAINT? n       SYS-PORT? n
  Translation-ID Number Mismatch Interval (days): _
change system-parameters security Page 2 of 2
    SECURITY-RELATED SYSTEM PARAMETERS
SECURITY VIOLATION NOTIFICATION PARAMETERS
SVN Station Security Code Violation Notification Enabled? y
Originating Extension: _____  Referral Destination: _____
Station Security Code Threshold: 10 Time Interval: 0:03
Announcement Extension: _____
STATION SECURITY CODE VERIFICATION PARAMETERS
                   Minimum Station Security Code Length: 4
Security Code for Terminal Self Administration Required? y
ACCESS SECURITY GATEWAY PARAMETERS
    MGR1? n INADS? n
 EPN? n      NET? n 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
891 Security-Related System Parameters 
17
SVN Station Security Code Violation 
Notification Enabled
Station Security codes are used to validate logins to a particular extension (for 
example, a home agent using an extender, or two part-time workers using the 
same telephone, but different extensions, through personal station access.) Enter 
y 
here to establish parameters for this.
Minimum Station Security Code Length
This determines the minimum required length of the Station Security Codes that 
you enter on the Station screen.
Security Code for Terminal Self Administration 
Required
Access Security Gateway Parameters
These eight fields appear only if the Access Security Gateway (ASG) field on the 
System-Parameters Customer-Options screen is 
y. 
The following 4 fields display only for the G3r version:
SYSAM-LCL 
A direct cable connection to the SYSAM-LCL G3-MT (local system 
administrator’s terminal) port on the System Access and Maintenance circuit pack 
on the active G3r processor carrier. For more information on the circuit pack, refer 
to the DEFINITY ECS System Description.
Valid entries Usage
3–8
Longer codes are more secure. If station security codes are 
used for external access to telecommuting features, the 
minimum length should be 7 or 8.
Valid entries Usage
y/n
Enter y to indicate that a security code is required.
Valid entries Usage
y/n
  Any entry attempt through this port receives a challenge 
response. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
892 Security-Related System Parameters 
17
SYSAM-RMT 
A dialed-in (or out) connection to the SYSAM-RMT port on the System Access 
and Maintenance circuit pack in the active G3r processor carrier. For more 
information on the circuit pack, refer to the DEFINITY ECS System Description. 
MAINT 
A direct connection to the EPN maintenance circuit pack RS-232 interface.
SYS-PORT 
A dialed-in (or out) connection to the System Access Port.
The following fields display only for the G3si and G3csi versions:
MGR1 
The direct connect system administration and maintenance access interface 
located on the processor circuit pack. For more information on the circuit pack, 
refer to the DEFINITY ECS System Description.
INADS 
A direct cable connection to the Initialization and Administration System used to 
remotely initialize and administer DEFINITY ECS.
Valid entries Usage
y/n
Any entry attempt through this port receives a challenge 
response.
Valid entries Usage
y/n
  Any entry attempt through this port receives a challenge 
response.
Valid entries Usage
y/n
  Any entry attempt through this port receives a challenge 
response.
Valid entries Usage
y/n
  Any entry attempt through this port receives a challenge 
response.
Valid entries Usage
y/n
Any entry attempt through this port receives a challenge 
response. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
893 Security-Related System Parameters 
17
EPN 
A direct connection to the Expansion Port Network.
NET 
A dialed-in (or out) connection to the Network Controller circuit pack. For more 
information on the circuit pack, refer to the DEFINITY ECS System Description.
Translation-ID Number Mismatch Interval (days)
A display-only field for all logins except init; only init logins can change this 
field. This field specifies the interval (in days) that the system allows a mismatch 
between the translation ID stored in the Processor circuit pack(s) and on the flash 
card. Following expiration of this interval, the ability to execute system 
administration commands that modify translation data is denied for all logins, 
except for init.
Valid entries Usage
y/n
Any entry attempt through this port receives a challenge 
response.
Valid entries Usage
y/n
Any entry attempt through this port receives a challenge 
response.
Valid entries Usage
1-90
Enter a number to indicate the number of days the system 
allows access to system administration commands. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
894 Site Data 
17
Site Data
Use this screen to enter information about buildings, floors and telephone set 
colors. You must supply values on this screen before you can enter information in 
the Site Data section of the Station screen.
Field descriptions for pages 1, 2 and 3
These pages are available for you to enter descriptive information about the 
buildings, floors and phone set colors. You may enter any valid keyboard 
character. If you want to indicate that a particular floor is in a particular building, 
you must include this in the floor entry, for example, B301-Fl4.
Station
This section provides descriptions of all of the fields that may appear on Station 
screens. Some of the fields are used for specific phone types; others are used for 
all phone types. To make it easier to find a specific field, they are listed in 
alphabetical order by field name.
Screen 184. Station
change site-data
SITE DATA USER DEFINITION
VALID BUILDING FIELDS 
_________ _________ _________ _________ _________
_________ _________ _________ _________ _________
_________ _________ _________ _________ _________
_________ _________ _________ _________ _________
_________ _________ _________ _________ _________
add station 1014 Page 1 of X
                                          STATION
Extension: 1014                                Lock Messages? n       BCC: 0
Type: 6408D+                         Security Code: ______   TN: 1
Port: _____ Coverage Path 1: ___     COR: 1
    Name: __________________________  Coverage Path 2: ___     COS: 1
                                             Hunt-to-Station: ____
STATION OPTIONS
              Loss Group: _ Personalized Ringing Pattern: 1
Data Module? n   Message Lamp Ext: 1014
Speakerphone: 2-way  Mute button enabled? y
Display Language? English
                                                        Media Complex Ext: 
                                                             IP Softphone? n 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
895 Station 
17
Screen 185. Station 
Screen 186. Station 
The standard station fields are organized alphabetically for easy access.
1-Step Clearing
Valid entries Usage
y/n
If set to y, the call terminates again at the WCBRI terminal 
when the user drops from the call.
add station 1014 Page 2 of X
STATION
FEATURE OPTIONS
LWC Reception? msa-spe  Auto Select Any Idle Appearance? n
         LWC Activation? y  Coverage Msg Retrieval? y
LWC Log External Calls? n Auto Answer: none
    CDR Privacy? n    Data Restriction? n
  Redirect Notification? y   Idle Appearance Preference? n
Per Button Ring Control? n
Bridged Call Alerting? n       Restrict Last Appearance? y
Active Station Ringing: single
        H.320 Conversion? n Per Station CPN - Send Calling Number? _
Service Link Mode: as-needed Special Character for Restricted Number? n
Multimedia Mode: basic
MWI Served User Type: ______   Display Client Redirection? n
AUDIX Name: Select Last Used Appearance? n
Messaging Server Name: ______ Coverage After Forwarding? _
Recall Rotary Digit? n  Multimedia Early Answer? n
add station 1014 Page 3 of X
STATION
     SITE DATA
          Room: _______                                      Headset? n
          Jack: ___                                          Speaker? n
         Cable: ___                                         Mounting: d
         Floor: _______                                  Cord Length: 0_
      Building: _______                                    Set Color: _____
ABBREVIATED DIALING
     List1: ________           List2: _________          List3: _________
BUTTON ASSIGNMENTS
 1: call-appr  5: ________
 2: call-appr  6: ________
 3: call-appr  7: ________
4: ________ 8: ________ 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
896 Station 
17
Abbreviated Dialing List1, List2, List3
You can assign up to 3 abbreviated dialing lists to each phone.
Active Station Ringing
Defines how call rings to the phone when it is off-hook. This field does not affect 
how calls ring at this phone when the phone is on-hook.
Valid entries Usage
enhanced
Allows the phone user to access the enhanced system 
abbreviated dialing list.
groupAllows the phone user to access the specified group 
abbreviated dialing list. If you enter 
group, you also must enter 
a group number.
personalAllows the phone user to access and program their personal 
abbreviated dialing list. If you enter 
personal, you also must 
enter a personal list number.
systemAllows the phone user to access the system abbreviated dialing 
list.
Valid entries Usage
continuous
Enter continuous to cause all calls to this phone to ring 
continuously.
single Enter single to cause calls to this phone to receive one ring 
cycle and then ring silently.
if-busy-singleEnter if-busy-single to cause calls to this phone to ring 
continuously when the phone is off-hook and idle and calls to 
this phone to receive one ring cycle and then ring silently when 
the phone is off-hook and active.
silentEnter silent to cause all calls to this station to just ring silently.