Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Instructions Manual

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
757 ISDN trunk group 
17
Design Considerations
ISDN-BRI and ISDN-PRI interfaces cannot be mixed in the same trunk group. 
Therefore, consider the following:
nThe earliest trunk member (the lowest numbered one) administered is 
considered correct.
nIf an offending member is subsequently found (meaning the first member 
was BRI and a later member was PRI, or vice versa), the cursor positions 
on the offending member, and the following error message appears:
Cannot mix BRI and PRI ports in the same trunk group.
Field descriptions for page 1
Many of the fields on the following screens are described in ‘‘
Trunk Group’’ on 
page 980. If a field on this screen is unique, it is listed and defined.
Screen 113. ISDN Trunk Group screen
The Calling Number – Delete, Insert, and Numbering Format fields are the 
administrable fields for the Calling Line Identification Prefix feature. They appear 
when the Direction field is incoming or two-way.
add trunk-group next  Page 1 of x
                                 TRUNK GROUP
 Group Number: xxx                  Group Type: isdn  CDR Reports: y
   Group Name: OUTSIDE_CALL_______________ COR: 1_       TN: 1__      TAC: ____
    Direction: two-way_       Outgoing Display? n          Carrier Medium: PRI/BRI
  Dial Access? n                Busy Threshold: 99_         Night Service: ____
 Queue Length: 0__
 Service Type: ________________      Auth Code? n            TestCall ITC: rest
Usage Alloc:_________________________Far End Test Line No: _______________
 TestCall BCC: 4 TestCall Service: ______________
 TRUNK PARAMETERS
          Codeset to Send Display: 6     Codeset to Send TCM,Lookahead: 6
         Max Message Size to Send: 260   Charge Advice: none_____________
   Supplementary Service Protocol: a  Digit Handling(in/out):overlap/overlap
Digit Treatment: insertion  Digits: 1234
             Trunk Hunt: cyclical  QSIG Value-Added Lucent? n
Digital Loss Group: __
Calling Number - Delete: ___ Insert: _______________ Numbering Format: _______
               Bit Rate: 1200_        Synchronization: async    Duplex: full
  Disconnect Supervision - In? y  Out? n
  Answer Supervision Timeout: 0__ 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
758 ISDN trunk group 
17
Calling Number – Delete
Calling Number – Insert
Calling Number – Numbering Format
This field indicates the TON/NPI encoding applied to CPN information modified 
by the CLI Prefix feature. This encoding does not apply to calls originating 
locally. The Numbering Format field on page 2 of this screen applies to calls 
originated from this switch.
If this field is blank, DEFINITY ECS passes on the encoding received in the 
incoming setup message. If the incoming setup message did not contain CPN 
information and digits are added, the outgoing message will contain these digits. 
If the Numbering Format field is blank in this case, the value defaults to pub-unk. 
If the Numbering Format field on page 2 of this screen is also administered as 
unknown, the trunk group is modified to “unk-unk” encoding of the TON/NPI. 
Therefore, this field also must contain a value other than 
unknown.
NOTE:
The values for this field map to the Type of Numbering (TON) and 
Numbering Plan Identifier (NPI) values shown below.
Valid entries Usage
1
 to 15Enter the number of digits, if any, to delete from the calling 
party number for all incoming calls on this trunk group.
all
blank
Valid entries Usage
1
 to 15Enter the specific digits, if any, to add to the beginning of the 
digit string of incoming calls when the calling party is a 
member of this trunk group.
blank
Valid entriesType of numbering 
(TON) Numbering plan identifier (NPI)
blank
incoming TON 
unmodifiedincoming NPI unmodified
natl-pubnational(2) E.164(1)
intl-pubinternational(1) E.164(1)
locl-publocal/subscriber(4) E.164(1)
pub-unkunknown(0) E.164(1) 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
759 ISDN trunk group 
17
Carrier Medium
This field lets you to specify the type of transport medium interface used for the 
ISDN trunk group. Appears only when the Group Type field is 
isdn and, on the 
System-Parameters Customer-Options screen, either the Async. Transfer Mode 
(ATM) Trunking or H.323 field is 
y.
Charge Advice
Use this field to accumulate and access charge information about a call. You 
already must have set the CDR Reports field to 
y or r (ring-intvl) before changing 
this field from its default of none. Remember that receiving Advice of Charge 
during the call (administered as “automatic” or “during-on-request”) affects 
system performance because of the increased ISDN message activity on the 
signaling channel, which may reduce the maximum call capacity.
lev0-pvtlocal(4) Private Numbering Plan - 
PNP(9)
lev1-pvtRegional Level 1(2) Private Numbering Plan - 
PNP(9)
lev2-pvtRegional Level 2(1) Private Numbering Plan - 
PNP(9)
unk-unkunknown(0) unknown(0)
Valid entries Usage
AT M
The trunk is implemented via the ATM Interface circuit pack.
IPThe trunk is implemented via the LAN/WAN (C-LAN)/MedPro 
Interface circuit pack as an H.323 trunk group.
PRI/BRIThe trunk is implemented as a standard DS1 or BRI interface.
Valid entriesType of numbering 
(TON) Numbering plan identifier (NPI) 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
760 ISDN trunk group 
17
Codeset to Send Display
This field defines the codeset for sending the information element for Display. 
The value depends on the type of switch to which the user is connected.
Codeset to Send National IEs
This field defines the codeset for sending the information element (IE) for 
national IEs. National IEs include all IEs previously sent only in code set 6 (such 
as DCS IE). Now these national IEs, including Traveling Class Marks (TCMs) 
and Lookahead Interflow (LAI), can be sent in code set 6 or 7. The value depends 
on the type of switch the user is connected to.
NOTE:
A Traveling Class Mark (that is, the user’s FRL or the user’s trunk group 
FRL) is passed between tandem nodes in an ETN in the setup message only 
when the Service Type field is 
tandem. It then is used by the distant tandem 
switch to permit access to facilities consistent with the originating user’s 
privileges.
Valid entries Usage
none
Enter none if you do not want the system to collect Advice of 
Charge information for this trunk group.
automaticEnter automatic only if your public network sends Advice of 
Charge information automatically.
end-on-
request Enter end-on-request if DEFINITY ECS must request charge 
information with each call, and you want to receive only the 
final call charge.
during-on-
request Enter during-on-request if DEFINITY ECS must request 
charge information with each call, and you want charges to 
display during and at the end of a call.
Valid entries Usage
0
CCITT
6Any other than CCITT or System 85 R2V4, 4E11 
7System 85 R2V4, 4E11
Valid entries Usage
6
Other types.
7System 85 R2V4, 4E11, or newer switch types  
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
761 ISDN trunk group 
17
Digit Handling (in/out)
This field defines whether overlap receiving and overlap sending features are 
enabled. Set the field to 
overlap when you want overlap receiving or overlap 
sending. Set to 
enbloc when you do not want these features enabled. The first 
field value indicates digit receiving and the second value indicates digit sending. 
There are 4 possible combinations:
 enbloc/enbloc, enbloc/overlap, 
overlap/enbloc, and overlap/overlap.
Without overlap receiving or sending enabled, the digits on incoming and 
outgoing calls are sent enbloc. If the Digit Handling field is 
overlap/enbloc or 
overlap/overlap, the following results:
— Incoming Call Handling Treatment table does not appear 
— The Digit Treatment and Digits fields appear
— Warning message indicates that all Incoming Call Handling entries are 
removed when screen is submitted
— When screen is submitted with these values, all Incoming Call Handling 
entries are removed
Far End Test Line No.
Specifies the number sent to the far-end’s ISDN test line extension. When the test 
trunk long command is issued, this exact number is sent to the far-end to establish 
a call that tests the integrity of the trunk member under test. The number does not 
pass through routing or undergo digit manipulation. The digits entered must be 
what the far-end expects. For example, for an ISDN tandem trunk, the far-end test 
number should be a 7-digit ETN (Electronic Tandem Network) number. Up to 15 
digits may be entered in this field. 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
762 ISDN trunk group 
17
Max Message Size to Send
Defines the maximum size of ISDN messages sent by the switch. Currently, the 
system can receive 260 byte messages. Valid entries are 
128, 244, 256, and 260.
The following table indicates the expected ISDN-PRI message size from several 
Lucent Technologies products.
QSIG Value-Added Lucent
Provides QSIG-VALU services. This field appears only if the Value-Added 
Lucent (VALU) field on the System-Parameters Customer-Options screen is 
y. 
This field can be set to 
y only if the Supplementary Service Protocol field on the 
System-Parameters Customer-Options screen is 
b. Valid entries are y and n. Blank 
is not a valid entry.
Service Type
Indicates the service for which this trunk group is dedicated. The following table 
provides a listing of predefined entries. In addition to the Services/Features listed 
in this table, any user-defined Facility Type of 0 (feature) or 1 (service) on the 
Network Facilities screen is allowed. 
Up to 10 (G3si, G3csi) or 200 (G3r) ISDN trunk groups can have this field 
administered as 
cbc.
ProductsMessage Length (octets) 
Received
4ESS (4E11) 256
4ESS (4E13) 256
4ESS (4E14) 256
5ESS (5E4) 244
5ESS (5E5) 244
5ESS (5E6) 244
System 75 (all) 260
System 85 (R2V4) 128
System 85 (R2V5) 260
System 85 (R2V6) 260 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
763 ISDN trunk group 
17
Valid entries Usage
access
A tie trunk giving access to an Electronic Tandem Network.
accunetACCUNET Switched Digital Service — part of ACI (AT&T 
Communications ISDN) phase 2.
cbcCall-by-Call service — provides different dial plans for different 
services on an ISDN trunk group. Indicates this trunk group is used 
by the Call-By-Call Service Selection feature.
dmi-mosDigital multiplexed interface — message oriented signaling.
i800International 800 Service — allows a subscriber to receive 
international calls without a charge to the call originating party.
inwatsINWATS — provides OUTWATS-like pricing and service for 
incoming calls.
ldsLong-Distance Service — part of ACI (AT&T Communications 
ISDN) phase 2.
megacomMEGACOM Service — an AT&T communications service that 
provides unbanded long-distance services using special access 
(switch to 4ESS switch) from an AT&T communications node.
mega800MEGACOM 800 Service — an AT&T communications service that 
provides unbanded 800 service using special access (4ESS switch to 
switch) from an AT&T communications node.
multiquestAT&T MULTIQUEST Telecommunications Service — dial 700 
service. A terminating-user’s service that supports interactive voice 
service between callers at switched-access locations and service 
provides directly connected to the AT&T Switched Network (ASN).
operatorNetwork Operator — provides access to the network operator.
outwats-bndOUTWATS Band — WATS is a voice-grade service providing both 
voice and low speed data transmission capabilities from the user 
location to defined service areas referred to as bands; the widest band 
is 5.
public-ntwrkPublic network calls — It is the equivalent of CO (outgoing), DID, or 
DIOD trunk groups. If Service Type is public-ntwrk, Dial Access can 
be set to 
y.
sddnSoftware Defined Data Network — provides a virtual private line 
connectivity via the AT&T switched network (4ESS switch). 
Services include voice, data, and video applications. These services 
complement the SDN service. Do not use for DCS with Rerouting.
Continued on next page 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
764 ISDN trunk group 
17
Supplementary Service Protocol
Indicates which supplementary service protocol to use for services over this trunk 
group. Supplementary Service protocols are mutually exclusive.
sdnSoftware Defined Network (SDN) — an AT&T communications 
offering that provides a virtual private network using the public 
switched network. SDN can carry voice and data between customer 
locations as well as off-net locations. 
sub-operatorPresubscribed Common Carrier Operator — provides access to the 
presubscribed common carrier operator.
tandemTandem tie trunks integral to an ETN
tieTie trunks — general purpose 
wats-max-bndMaximum Banded Wats — a WATS-like offering for which a user’s 
calls are billed at the highest WATS band subscribed to by users.
Valid entries Usage
a
National public network/Shared UUI (for ISDN-BRI)
National public network (for ISDN-PRI)
bISO/ETSI QSIG Private Network
cETSI public network
dEuropean Computer Manufacturer’s Association (ECMA) 
QSIG private network (supports only Name Identification and 
Additional Network Feature Transit Counter (ANF-TC))
eDCS with Rerouting
— Do not use the Service Type field entry of 
dmi-mos or 
sddn with this option.
— Set the Used for DCS field (on page 2) to 
y.
fISDN Feature Plus
Public network feature plus signaling.
Valid entries Usage
Continued on next page 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
765 ISDN trunk group 
17
Test Call BCC
Indicates the Bearer Capability Code (BCC) used for the ISDN test call.
Testcall ITC
Controls the encoding of the Information Transfer Capability (ITC) codepoint of 
the bearer capability IE in the SETUP message when generating an ISDN test call. 
Allowed values are 
rest (restricted) and unre (unrestricted).
NOTE:
ISDN Testcall feature has no routing, so a testcall is never blocked 
due to an incompatible ITC.
Testcall Service
Specifies the call-by-call selection for an ISDN test call. Only appears if the 
Service Type field is cbc. Valid entries are all of the services listed in ‘‘
Service 
Type’’ on page 762, excluding sddn or any new Facility Type of 0 (feature), 1 
(service), or 3 (outgoing) that is defined by users on the Network Specific Facility 
Encoding screen.
Trunk Hunt
The switch performs a trunk hunt when searching for available channels within a 
facility in an ISDN trunk group. Enter 
ascend to enable a linear trunk hunt search 
from the lowest to highest numbered channels, or 
descend for a linear trunk hunt 
search from the highest to lowest numbered channels. With both 
ascend and 
descend, all trunks within an ISDN trunk group are selected based on this field 
and without regard to the order in which trunks are administered within the trunk 
group.
Enter 
cyclical to enable a circular trunk hunt based on the sequence the trunks 
were administered within the trunk group. When using ISDN-BRI interfaces, only 
cyclical is allowed.
NOTE:
The cyclical option cannot be set if the trunk group using ISDN-PRI 
interfaces is to be used for Wideband operations (the Wideband Support 
field set to 
y).
Valid entries Usage
0
Voice
1Mode 1
2Mode 2 Asynchronous
3Mode 3 Circuit
4Mode 0 
						

							DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
766 ISDN trunk group 
17
The search can be administered per ISDN-PRI trunk group, but it infers the 
direction of search within all ISDN-PRI facilities (or portions of those facilities) 
administered within the trunk group.
Usage Alloc
Appears when the Service Type field is 
cbc. Specifies whether users want to 
allocate the services provided by the trunk group. Valid entries are 
y and n. If y is 
entered, two additional CBC-related screens display. They are the CBC Trunk 
Group Usage Allocation Plans screen and the CBC Trunk Group Usage 
Allocation Plan Assignment Schedule.
Field descriptions for page 2
Screen 114. ISDN Trunk Group screen
add trunk-group next  Page 2 of x
TRUNK FEATURES
ACA Assignment? n            Measured: none____  Wideband Support? n
Long Holding Time (hours): _ Internal Alert? _ Maintenance Tests? y
Short Holding Time (sec): _ Data Restriction? n  NCA-TSC Trunk Member: 7
  Short Holding Threshold: __  Send Name: n      Send Calling Number: n
             Used for DCS? n          Hop Dgt: n
    Suppress # Outpulsing? n  Numbering Format: ______ DCS Signaling: ____
Outgoing Channel ID Encoding: _________  UUI IE Treatment: shared
Maximum Size of UUI IE Contents: 128
  Replace Restricted Numbers? n
  Replace Unavailable Numbers? n
Send Connected Number: y
Send UCID? n   
Send Codeset 6/7 LAI IE? y 
Path Replacement Method: better-route    US NI Delayed Calling Name Update? n